Amazon Black Friday Week deals

Paid link

Routers · How-to guide

How to Use a Router as a Wi-Fi Extender

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

A spare router can extend your Wi-Fi when it has a repeater, access point or mesh mode. Place it where it still gets a strong signal from the main router, connect it by cable where you can, and give it the same network name and password. Check the mode on the spare router first, since not every router below offers a repeater, access point or mesh mode.

  1. Check for a repeater or mesh mode

    Open the settings of the spare router and look for a repeater, access point, extender or mesh mode. The Deco X55 is a mesh system, the Archer AX21 supports Easy Mesh, and the eero 6 uses TrueMesh to route traffic between units. Check the manual before you start to confirm the mode is there.

  2. Connect by cable where you can

    A cable link between the two routers avoids a wireless hop. The Deco X55 has 3 Gigabit Ethernet ports per unit and supports wired Ethernet backhaul. The Nighthawk R6700AX has four 1 Gig Ethernet LAN ports and a separate 1 Gig WAN port for the modem or gateway. Where no cable run is possible, the second router repeats the signal over Wi-Fi instead.

  3. Place the second router halfway

    Put the second router where it still gets a strong signal from the main router, about halfway to the dead zone, and not inside the dead zone itself. Walls, floors and interference can reduce range, so move it closer to the main router if the link drops. The Deco X55 covers up to 6500 square feet as a 3-pack, and the eero 6 and the Nighthawk R6700AX each cover up to 1,500 sq. ft.

  4. Match the network name and password

    Give the second router the same network name and password as the main router so your devices move between them without a new login. Set it up through the maker's app: the Deco app, the eero app and the Nighthawk app each walk you through setup with guided steps. After setup, walk to the far room and check that your phone or laptop stays connected.

What you need

TP-Link Deco X55 AX3000

TP-Link Deco X55 AX3000

A Wi-Fi 6 mesh system with 3 Gigabit Ethernet ports per unit, wired Ethernet backhaul and coverage up to 6500 square feet as a 3-pack.

View on Amazon
Amazon eero 6 mesh

Amazon eero 6 mesh

A Wi-Fi 6 mesh router that covers up to 1,500 sq. ft., supports plans up to 900 Mbps and connects 75+ devices.

View on Amazon
TP-Link AX1800 WiFi 6 Router

TP-Link AX1800 WiFi 6 Router

A Wi-Fi 6 router with Easy Mesh, dual-band AX1800 and four high-gain antennas for coverage far from the router.

View on Amazon
NETGEAR Nighthawk

NETGEAR Nighthawk

A Wi-Fi 6 dual-band router with four 1 Gig Ethernet LAN ports, a separate WAN port and coverage up to 1,500 sq. ft.

View on Amazon

These come from our ranked list Best Wi-Fi Router, which compares them spec by spec.

FAQ

Can any router work as a Wi-Fi extender?

No. The spare router needs a repeater, access point, extender or mesh mode. The Deco X55, the Archer AX21 and the eero 6 all support mesh, so check the mode in the manual before you start.

Is a cable link better than a wireless link?

A cable link avoids a wireless hop between the routers. The Deco X55 supports wired Ethernet backhaul, and the Nighthawk R6700AX has four 1 Gig Ethernet LAN ports for wired devices.

Do the two routers need the same password?

Yes, use the same network name and password on both so devices move between them without a new login. Check the settings on each router after setup to confirm they match.

Ranked routers guides