How to Use a Router
To use a router, connect it to your modem with an Ethernet cable, plug it in, and set up the Wi-Fi name and password in the maker's app. Then connect your phones, laptops and other devices to that network. The steps below walk through the connection, the placement, the setup and the daily use.
Connect the router to the modem
Plug one end of an Ethernet cable into the modem and the other end into the WAN or internet port on the router. Then plug the router into power and wait until its lights settle. A router needs a modem to reach the internet, so keep both boxes switched on. If your modem is also a router, you may need bridge mode before the new router works as expected.
Place the router in a central spot
Put the router in the open, near the middle of your home, and raised off the floor on a shelf or table. Walls, floors and interference can reduce range, so keep it away from thick walls, metal objects and large appliances. A central spot gives the rooms around it a fair share of the signal. If a far room still gets a weak signal, move the router a little and check again.
Set the network name and password
Open the app for your router and follow its setup steps. The Deco app gives visual guidance for setup, the eero app walks you through it, and the Nighthawk app gives guided setup. Give the network a name you will recognize, set a password, and save the settings. Write the password down so you can add new devices later without resetting the router.
Connect phones, laptops and other devices
On each device, open the Wi-Fi list, pick the network name you set, and enter the password. A device that stays close to the router gets a good signal, so use a cable for a desktop or a game console that sits beside it. Plug an Ethernet cable into a LAN port on the router for a wired connection. Repeat the steps for each new device you add.
Add coverage and keep the router updated
If a room still gets a weak signal, add another mesh unit or move a unit closer to that room. The Deco X55 3-pack covers up to 6500 square feet, and eero hardware lets you add more units as your needs change. Turn on automatic updates in the app when your router offers them, since the eero 6 and the Nighthawk R6700AX both update firmware on their own. Check the app from time to time for new settings.
What you need

TP-Link Deco X55 AX3000
A Wi-Fi 6 mesh system in a 3-pack that covers up to 6500 square feet, with 3 Gigabit ports per unit and Ethernet backhaul.
View on Amazon
Amazon eero 6 mesh
A Wi-Fi 6 mesh router that covers up to 1,500 square feet, supports internet plans up to 900 Mbps, and sets up through the eero app.
View on Amazon
TP-Link AX1800 WiFi 6 Router
A Wi-Fi 6 dual-band router with AX1800 speed class, 4 high-gain antennas, and a Tether app for firmware checks.
View on Amazon
NETGEAR Nighthawk
A Wi-Fi 6 dual-band router with 4 Gigabit LAN ports, a WAN port, and the Nighthawk app for guided setup and guest networks.
View on AmazonThese come from our ranked list Best Wi-Fi Router, which compares them spec by spec.
FAQ
Do I need a modem with a router?
Yes, for most internet service providers. The router shares the connection around your home, while the modem brings the internet into the home. Connect the modem to the router's WAN port with an Ethernet cable.
Where should I put my router?
In the open near the middle of your home, raised off the floor. Walls, floors and interference can reduce range, so keep it away from thick walls and metal objects. Move it a little at a time if a far room gets a weak signal.
Can I add more units to a mesh system?
Yes. The Deco X55 comes as a 3-pack, and eero lets you add more units as your needs change. Place the extra unit between the router and the room with the weak signal, then follow the app to join it to the network.



