How to Set Up Mesh Wi-Fi at Home
A mesh Wi-Fi system uses a main unit and extra units that work together as one network, so your devices stay on the same network name as you move around your home. You set up the main unit first, then add the other units where the signal is weak. The steps below walk through placement, setup, and checking the network after it is running.
Connect the main unit to the modem
Plug the main unit into power and connect it to your modem with an Ethernet cable. If your modem is also a router, check the manual for how to put it in bridge mode or turn off its Wi-Fi, so the mesh system runs the network. Wait until the light on the main unit shows it is ready, then move on to setup. Keep the main unit out in the open, away from thick walls and metal objects, and near the center of the area you want to cover first.
Set up the network in the app
Download the app for your mesh system and create an account if the app asks for one. Follow the prompts to name the network and set a password, then let the app find the main unit and finish the first part of setup. Choose a network name and password you can remember, and write the password down and keep it with the main unit. When the app says the main unit is online, check the connection with a phone or laptop before you add the other units.
Place the extra units in open spots
Place each extra unit in an open spot, about halfway between the main unit and the room with a weak signal. Keep units off the floor, away from thick walls, large metal objects, and closed cabinets, and plug each one into power. Avoid putting a unit in a room where the signal is already gone, since it needs a clear signal from the unit before it. Let each unit join the network and show it is online before you move on to the next one.
Check the signal in each room
Walk through your home with a phone or laptop and open a page or a video in each room to see how the network holds up. Note the rooms where pages load slowly or a video stops, and move the nearest unit a short distance toward the main unit or into a more open spot. Check the signal again after each move, and leave the unit where the connection stays steady. Do not place units too close together, since a unit that sits next to the main unit adds little coverage.
Update the firmware and change the password
Open the app and check for a firmware update, then install it if one is available and wait until the units come back online. Change the default admin password if your system has one, and keep the Wi-Fi password strong, with a mix of letters and numbers that others cannot guess. Turn on the guest network if you want visitors to have Wi-Fi without the main password, and turn off any network name you do not use.
What you need

TP-Link Deco S4 Mesh AC1900
A 3-pack Wi-Fi 5 mesh system with AC1900 dual-band speeds, coverage up to 5,500 sq. ft., two Gigabit Ethernet ports on each unit, and parental controls.
View on Amazon
TP-Link Deco S4 Whole Home Mesh
A 2-pack Wi-Fi 5 mesh system with AC1900 dual-band speeds, coverage up to 3,800 sq. ft., two Gigabit Ethernet ports on each unit, and parental controls.
View on Amazon
Amazon eero 7 dual-band mesh
A 2-pack Wi-Fi 7 mesh router with support for internet plans up to 2.5 Gbps, coverage up to 4,000 sq. ft., and two 2.5 GbE ports.
View on Amazon
Amazon eero 7 dual-band mesh
A 3-pack Wi-Fi 7 mesh router with support for internet plans up to 2.5 Gbps, coverage up to 6,000 sq. ft., and two 2.5 GbE ports.
View on AmazonThese come from our ranked list Best Mesh Router, which compares them spec by spec.
FAQ
Do I need a modem for a mesh Wi-Fi system?
Yes. The mesh system creates your Wi-Fi network, but the modem brings the internet connection into your home. Connect the main unit to the modem, and check with your internet provider if you are not sure which modem you have.
Where should I put the satellite units?
Put each unit in an open spot between the main unit and the area with a weak signal, and keep it off the floor and away from thick walls and metal objects. A unit placed where the signal is already gone cannot pass the network on, so move it closer to the main unit.
Can I use my old router with a mesh system?
You can, but it is simpler to let the mesh system run the network on its own. If you keep the old router, turn off its Wi-Fi or put it in bridge mode, so you do not end up with two networks that fight over your devices.



