How to Connect a Router as a Wi-Fi Extender
You can use a spare router as a Wi-Fi extender by turning off its routing job and letting the main router hand out addresses. Connect the spare router to the main router with an Ethernet cable, give it the same network name and password, and place it where the main signal fades. A mesh system does the same job with less setup.
Check that the spare router can extend
A spare router can extend a network as an access point or as part of a mesh system. In access point mode it stops routing and passes traffic to the main router, so devices on either box share one network. Some routers have a mode for this in their settings, and mesh systems such as the TP-Link Deco X55 and the eero 6 add a unit through the app instead. Check the settings page of the spare router for an access point or bridge mode before you start.
Connect the spare router with a cable
Run an Ethernet cable from a LAN port on the main router to a LAN port on the spare router when you use access point mode, so the spare router gets its connection over the wire. The NETGEAR Nighthawk R6700AX has four 1 Gig LAN ports for wired devices. A cable link keeps the extender's signal steady and leaves the Wi-Fi bands free for devices.
Turn off the spare router's DHCP
Open the spare router's settings and turn off DHCP, so only the main router hands out addresses. If the spare router also hands out addresses, devices can end up on separate networks and lose each other. Give the spare router an address on the main network if its settings ask for one, then save and restart it.
Match the network name and password
Set the spare router to broadcast the same network name and password as the main router, on the same bands, so phones and laptops move between them without asking for a new password. Keep the security type the same on the spare router and the main router. A device stays on the first router it joined until that signal drops, so it may hold a weak signal before it moves to the spare router.
Place the extender and check the signal
Put the spare router where the main signal is still usable but near the dead zone, not inside it. Plug it in, connect a phone to the network, and walk to the far room to check that pages load. If the signal is weak, move the spare router closer to the main router and check again.
What you need

TP-Link Deco X55 AX3000
A Wi-Fi 6 mesh system that covers up to 6500 square feet, with 3 Gigabit Ethernet ports per unit and support for Ethernet backhaul.
View on Amazon
Amazon eero 6 mesh
A Wi-Fi 6 mesh router that covers up to 1,500 sq. ft. and supports internet plans up to 900 Mbps, with setup through the eero app.
View on Amazon
TP-Link AX1800 WiFi 6 Router
A dual-band Wi-Fi 6 router with Easy Mesh, AX1800 speed class, and 4 high-gain antennas for coverage.
View on Amazon
NETGEAR Nighthawk
A dual-band Wi-Fi 6 router with a separate 1 Gig WAN port, four 1 Gig LAN ports, and coverage up to 1,500 sq. ft.
View on AmazonThese come from our ranked list Best Wi-Fi Router, which compares them spec by spec.
FAQ
Can any router work as a Wi-Fi extender?
A router can work as an access point when you turn off DHCP and connect it by cable to the main router. Mesh systems such as the TP-Link Deco X55 and the eero 6 extend the network by adding a unit through the app. Check the spare router's settings for an access point mode first.
Do I need a cable to connect a router as an extender?
A cable gives the steadiest link between the main router and the spare router. Some mesh systems can link over Wi-Fi instead, and the Deco X55 supports Ethernet backhaul for a wired link between units. If you use Wi-Fi to link them, place the spare router where the main signal is still strong.
Why do devices drop when I move between routers?
Devices can drop if the spare router hands out addresses on a separate network, which happens when DHCP stays on in the spare router. Turn off DHCP in the spare router so only the main router hands out addresses. Matching the network name and password also helps devices move between the routers.




