How to Connect a Fiber Optic Cable to a Router
A fiber optic cable does not plug straight into a router. It plugs into the modem your provider supplies, and an Ethernet cable runs from the modem to the WAN port on the router. The Nighthawk R6700AX has a separate 1 Gig WAN port for that cable, and a modem is required for most internet service providers.
Find the modem and the fiber port
Find the modem your provider installed and look for the port where the fiber cable connects. The fiber cable ends in a small connector that clicks into that port, and the modem turns the light signal into an Ethernet signal for the router. Do not look into the end of a fiber cable while it is connected, and do not bend the cable into a sharp kink. If you cannot find a fiber port on the modem, contact your provider before you plug anything in.
Connect the fiber cable to the modem
Push the fiber connector into the modem port until it clicks, and check that it sits straight and fully seated. Do not force it if it does not fit, since the connector only goes in one way. Power on the modem and wait until its lights show it is online. A modem is required for most internet service providers, so a router alone cannot take the fiber connection.
Run an Ethernet cable to the router
Take an Ethernet cable and plug one end into the Ethernet port on the modem and the other end into the WAN port on the router. On the NETGEAR Nighthawk R6700AX, the WAN port is a separate 1 Gig port next to four 1 Gig LAN ports. On the TP-Link Deco X55, each unit has 3 Gigabit Ethernet ports, and any of them can work as the router port. Do not plug the modem cable into a LAN port.
Power on the modem, then the router
Plug in the modem first and let it come fully online, with its internet light steady. Then plug in the router and let it start up. The router needs the modem online before it can get an address from your provider, so starting the modem first avoids a failed setup. If your modem is a gateway or a modem router combo, it may need bridge mode first. The Nighthawk R6700AX pairs with a modem or gateway, and some gateways and modem router combos may require bridge mode.
Finish setup and check the connection
Open the router app and follow its steps to name the network and set a password. The Deco app helps you set up the Deco X55, the eero app walks you through setup on the eero 6, and the Nighthawk app gives guided setup on the Nighthawk R6700AX. Connect a phone or laptop to the new Wi-Fi network and open a web page. If the page loads, the fiber link through the modem and the router works.
What you need

TP-Link Deco X55 AX3000
A Wi-Fi 6 AX3000 mesh system with 3 Gigabit Ethernet ports per unit, so the modem cable and wired devices share the same box.
View on Amazon
Amazon eero 6 mesh
A Wi-Fi 6 mesh router that supports internet plans up to 900 Mbps and covers up to 1,500 sq ft.
View on Amazon
TP-Link AX1800 WiFi 6 Router
A dual-band Wi-Fi 6 router with AX1800 speed class, 4 high-gain antennas and Easy Mesh support.
View on Amazon
NETGEAR Nighthawk
A dual-band Wi-Fi 6 router with a separate 1 Gig WAN port and four 1 Gig LAN ports for the modem cable.
View on AmazonThese come from our ranked list Best Wi-Fi Router, which compares them spec by spec.
FAQ
Can I plug a fiber optic cable straight into a router?
No. The fiber cable plugs into the modem your provider supplies, and an Ethernet cable runs from the modem to the WAN port on the router. A modem is required for most internet service providers.
What if my modem is also a router?
Some gateways and modem router combos may require bridge mode. The Nighthawk R6700AX pairs with a modem or gateway, and bridge mode lets the router handle the network. Connect the gateway Ethernet port to the router WAN port.
Do I need a modem for a fiber connection?
Yes. A modem is required for most internet service providers, and the Deco X55 works with all of them. Connect the modem to the router WAN port with an Ethernet cable, then power on the modem first and the router second.




