Amazon Black Friday Week deals

Paid link

Routers · How-to guide

How to Connect Your Router

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To connect a router, plug an Ethernet cable from your modem into the router, plug the router into power, and wait for its lights to settle. Then connect a phone or laptop to the router, either by cable or over Wi-Fi, and follow the setup steps in the router app. Once the app finishes, your devices can join the new network.

  1. Plug the modem into the router

    Find the WAN port on the router, marked WAN or Internet, and plug an Ethernet cable from your modem into it. The NETGEAR Nighthawk has a separate 1 Gig WAN port that connects to your modem or gateway. If your modem has a power switch, switch the modem off, plug in the cable, then switch the modem back on. A firm click means the cable is seated, so check that both ends are pushed in.

  2. Power the router on and wait

    Plug the router into power and wait for its lights to stop changing. The lights show that the router has started and is ready for the next step. Do not unplug the router while it starts up. When the lights hold steady, move on to connecting a device.

  3. Connect a phone or laptop

    Connect a phone or laptop to the router with an Ethernet cable or over Wi-Fi. A wired link goes into a LAN port on the router, and the NETGEAR Nighthawk has four 1 Gig Ethernet LAN ports for wired devices. For Wi-Fi, pick the network name the router shows, on the 2.4 GHz or 5 GHz band, and enter the Wi-Fi password. If no network name shows, check the cable and the lights again.

  4. Finish setup in the router app

    Open the router app on your phone and follow its setup steps. The Deco app helps you set up your network with clear visual guidance, the eero app walks you through setup, and the Nighthawk app gives guided setup for the NETGEAR Nighthawk. Give the network a name you will recognize, set a password, and connect your other devices to the new name. If a step fails, close the app, check the cables, and run the setup again.

What you need

TP-Link Deco X55 AX3000

TP-Link Deco X55 AX3000

A Wi-Fi 6 mesh system with AX3000 speed class, 3 Gigabit Ethernet ports per unit, and support for Ethernet backhaul.

View on Amazon
Amazon eero 6 mesh

Amazon eero 6 mesh

A Wi-Fi 6 mesh router that covers up to 1,500 sq. ft., supports speeds up to 900 Mbps, and connects 75+ devices.

View on Amazon
TP-Link AX1800 WiFi 6 Router

TP-Link AX1800 WiFi 6 Router

A dual-band Wi-Fi 6 router with AX1800 speed class, 1.8 Gbps total bandwidth, and 4 high-gain antennas.

View on Amazon
NETGEAR Nighthawk

NETGEAR Nighthawk

A dual-band Wi-Fi 6 router with AX1800 speed class, 4 Gigabit LAN ports, and a separate 1 Gig WAN port.

View on Amazon

These come from our ranked list Best Wi-Fi Router, which compares them spec by spec.

FAQ

Do I need a modem to connect a router?

Yes, for most internet service providers. The Deco X55 works with all internet service providers, and a modem is required for most of them. The Archer AX21 also works with all internet service providers, and all Wi-Fi routers require a separate modem.

What do I plug into the WAN port?

Plug an Ethernet cable from your modem into the WAN port. The NETGEAR Nighthawk has a separate 1 Gig WAN port that connects to your modem or gateway. The Deco X55 has 3 Gigabit Ethernet ports per unit.

How do I connect more devices after setup?

Join your devices to the network name you set, on the 2.4 GHz or 5 GHz band. The Deco X55 connects up to 150 devices, the eero 6 connects 75+ devices, and the NETGEAR Nighthawk covers up to 20 connected devices. Wired devices can use a LAN port on the router.

Ranked routers guides