Amazon Black Friday Week deals

Paid link

Routers · How-to guide

How to Connect Mesh Wi-Fi to an Existing Router

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To connect mesh Wi-Fi to an existing router, plug the main mesh unit into the existing router with an Ethernet cable, then set the mesh system to bridge or access point mode so the existing router keeps routing. The mesh units then share a single network name, and switching the old router's Wi-Fi off keeps devices on the mesh. The steps below walk through the setup in order.

  1. Decide which device routes the network

    A home network works best when a single device hands out addresses and manages traffic. With mesh Wi-Fi added to an existing router, that job can stay with the existing router while the mesh units handle the Wi-Fi. The mesh system then runs in bridge mode or access point mode, and the existing router keeps its role. Check the mesh app for a bridge or access point setting before plugging anything in, so the setup follows the mode you picked.

  2. Connect the main unit to the router

    Run an Ethernet cable from a LAN port on the existing router to the WAN or Internet port on the main mesh unit. Plug the mesh unit into power and let its light settle before opening the app. The app then walks through naming the network and setting a password. Keep the main unit near the existing router for this step, since the cable between them sets the link for the whole mesh.

  3. Switch the mesh to bridge mode

    In the mesh app, find the mode setting and switch it to bridge mode or access point mode. This hands routing back to the existing router and stops the mesh from handing out addresses of its own. The mesh then passes traffic through, and devices on the wired ports and on Wi-Fi sit on the same network. Save the setting and let the units restart if the app asks, then check that a phone or laptop still reaches the internet.

  4. Turn off Wi-Fi on the old router

    With the mesh running, the old router's Wi-Fi becomes a second network with the same job, and devices can cling to the weaker signal as you move through the home. Open the old router's settings and switch its Wi-Fi off, leaving the mesh as the network your devices join. If the old router keeps its Wi-Fi on, forget the old network name on your devices so they stay on the mesh.

  5. Place the extra units and check the link

    Place each extra unit within reach of the main unit or the next unit along, in the open and off the floor, where its signal passes through as few walls as possible. Open the mesh app and check that each unit shows as connected, then walk through the home with a phone and watch it stay on the network. A unit that shows as offline needs a shorter hop to its neighbor, so move it closer and check again.

What you need

TP-Link Deco S4 Mesh AC1900

TP-Link Deco S4 Mesh AC1900

A Wi-Fi 5 AC1900 mesh system with 3 units covering up to 5,500 sq ft, 2 Gigabit Ethernet ports on each unit and wired backhaul.

View on Amazon
TP-Link Deco S4 Whole Home Mesh

TP-Link Deco S4 Whole Home Mesh

A Wi-Fi 5 AC1900 mesh system with 2 units covering up to 3,800 sq ft, 2 Gigabit Ethernet ports on each unit and wired backhaul.

View on Amazon
Amazon eero 7 dual-band mesh

Amazon eero 7 dual-band mesh

A dual-band Wi-Fi 7 router with two auto-sensing 2.5 GbE ports, supporting internet plans up to 2.5 Gbps and 120+ devices across 4,000 sq ft.

View on Amazon
Amazon eero 7 dual-band mesh

Amazon eero 7 dual-band mesh

A dual-band Wi-Fi 7 router with two auto-sensing 2.5 GbE ports, supporting internet plans up to 2.5 Gbps and 120+ devices across 6,000 sq ft.

View on Amazon

These come from our ranked list Best Mesh Router, which compares them spec by spec.

FAQ

Can I use mesh Wi-Fi with my existing router?

Yes. Connect the main mesh unit to the existing router with an Ethernet cable and set the mesh to bridge or access point mode. The existing router keeps routing, and the mesh handles the Wi-Fi.

Should I turn off Wi-Fi on my old router?

Yes, when the mesh is running. Two networks with the same job can hold devices on the weaker signal as you move through the home. Switching the old Wi-Fi off leaves the mesh as the network your devices join.

Which port do I plug the mesh unit into?

Plug an Ethernet cable into a LAN port on the existing router and into the WAN or Internet port on the main mesh unit. The mesh app then walks through naming the network and setting a password.

Ranked routers guides