Amazon Black Friday Week deals

Paid link

Storage · How-to guide

How to Install an NVMe SSD

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To install an NVMe SSD, shut the computer down, unplug it, and open the case following the maker's manual. Find the M.2 slot on the board, slide the drive into the slot, and fasten it with the screw and standoff. Then close the case, start the computer, and check that the drive appears before you use it.

  1. Shut down and unplug the computer

    Shut the computer down fully and unplug the power cable before you open the case. Follow the maker's manual for your computer to open the case and find the parts inside. Work on a clear, dry surface with the case steady, and keep the drive in its packaging until you are ready to fit it.

  2. Check the M.2 slot first

    An NVMe drive fits an M.2 slot on the board, not a drive bay. Check the board or laptop manual for the slot that supports NVMe and for the connector the drive uses. The drives in the list below are 2.5-inch SATA drives, so they fit a SATA drive bay rather than an M.2 slot.

  3. Seat the drive in the slot

    Hold the drive by its edges and slide its connector into the M.2 slot. Press the far end of the drive down toward the board until it sits flat on the standoff. Fasten it with the screw that came with the board or the drive, and tighten it only until it holds the drive in place.

  4. Close the case and start up

    Replace the side panel or base cover and fasten it as the manual shows, then plug the power cable back in and start the computer. Open the setup screen or the system settings and check that the new drive is listed. If the drive does not appear, shut the computer down, unplug it, and check that the drive is seated and fastened.

  5. Set up the drive before use

    A new drive needs to be set up in your operating system before it can hold files. Open the disk tool in your system settings and follow its steps to prepare the drive, then check that it appears with the rest of your storage. Follow the drive maker's instructions if the tool asks for a choice you do not recognize.

What you need

PNY CS900 500GB 2.5" SATA III Internal

PNY CS900 500GB 2.5" SATA III Internal

A 500GB 2.5-inch SATA III SSD with rated read speeds up to 550 MB/s, for a laptop or desktop with a SATA drive bay.

View on Amazon
SanDisk SSD Plus

SanDisk SSD Plus

A 500GB 2.5-inch SATA III SSD with rated read speeds up to 545 MB/s, for a laptop or desktop with a SATA drive bay.

View on Amazon
PNY CS900 250GB 2.5" SATA III Internal

PNY CS900 250GB 2.5" SATA III Internal

A 250GB 2.5-inch SATA III SSD with rated read speeds up to 535 MB/s, for a laptop or desktop with a SATA drive bay.

View on Amazon
Kingston 960GB A400 SATA3 2.5" Internal SSD

Kingston 960GB A400 SATA3 2.5" Internal SSD

A 960GB 2.5-inch SATA3 SSD for a laptop or desktop with a SATA drive bay, as a replacement for a hard drive.

View on Amazon

These come from our ranked list Best Internal SATA SSD, which compares them spec by spec.

FAQ

Can I install an NVMe SSD in a laptop?

It depends on the laptop. Check the manual for an M.2 slot that supports NVMe. An NVMe drive fits where the manual lists an M.2 slot that supports NVMe.

Do I need a screw to install an NVMe SSD?

Boards hold the drive with a screw and a standoff in the M.2 slot. Use the screw and standoff that came with the board or the drive, and follow the board manual.

What is the difference between NVMe and SATA drives?

An NVMe drive fits an M.2 slot on the board, while a SATA drive connects through a SATA port and often comes in a 2.5-inch size. The drives below are 2.5-inch SATA drives, so they fit a SATA bay rather than an M.2 slot.

Ranked internal ssds guides