How to Install an SSD in a Laptop
To install an SSD in a laptop, shut the laptop down, unplug it, open the bottom panel following the maker's manual, find the drive slot, fit the new SSD, close the panel, then set up the drive in your OS. Laptops take either a 2.5-inch SATA drive or an M.2 drive, so check which slot your laptop has before you buy.
Back up your files first
Copy your files to an external drive or a cloud account before you open the laptop. If you plan to move your OS to the new SSD, make a full system image or a recovery drive with the tools in your OS, and keep the license key or sign-in details for your software where you can reach them. A backup also protects you if the old drive fails during the swap or if you pick the wrong drive to remove.
Check which drive slot your laptop has
Open your laptop's manual or the maker's support page and look for the storage section. It names the drive type the laptop accepts, such as a 2.5-inch SATA bay or an M.2 slot, and the length the slot fits, such as M.2 2280. Some thin laptops have the drive soldered in place, so check the manual before you buy.
Shut down and open the laptop
Shut the laptop down, unplug the charger and any cables, then work on a clean, flat surface. Follow the maker's manual to remove the bottom panel screws and lift the panel, keeping the screws in a small tray so you can find them again. Touch a metal part of the laptop chassis first to discharge static, and do not force the panel if it resists. If your laptop is still under warranty, contact the maker before you open it.
Fit the new SSD
For a 2.5-inch SATA drive, slide it into the bay or the caddy, connect the SATA cable or connector, and fix it with the screws from the bay. For an M.2 drive, slide it into the slot at a slight angle, press it down flat, and hold it with the small screw at the end of the slot. Handle the drive by its edges and keep it away from liquids.
Set up the drive and check it works
Close the panel, replace the screws, plug the charger in and switch the laptop on. If the new drive holds your OS, install it from your recovery drive or installation media and follow the on-screen steps. If it is an extra drive for storage, open your OS's disk tool, format it, then check that it shows the full capacity you expect.
What you need

Lexar 1TB NM790 NVMe SSD w/Heatsink
A 1TB M.2 2280 NVMe SSD with read speeds up to 7400 MB/s, a heatsink, and a five-year limited warranty.
View on Amazon
Samsung SSD 9100 PRO
A 2TB PCIe 5.0x4 M.2 2280 NVMe SSD with read speeds up to 14,700 MB/s and a 5 Year Manufacturer warranty.
View on Amazon
TEAMGROUP T-Force Vulcan Z
A 1TB 2.5-inch SATA III SSD with read and write speeds up to 550/500 MB/s and a 3-year limited warranty.
View on Amazon
Crucial P310 1TB SSD
A 1TB PCIe Gen4 NVMe M.2 2280 SSD with read speeds up to 7,100 MB/s, listed for laptops, and a 5-year limited warranty.
View on AmazonThese come from our ranked list Best Internal SSD for Laptop, which compares them spec by spec.
FAQ
Do I need to clone my old drive first?
Only if you want to keep your files, programs and settings as they are. Cloning copies the old drive to the new SSD, so the laptop starts up the same way. If you prefer a fresh start, install the OS from recovery media instead.
Can I install an SSD in any laptop?
No. Some laptops have the storage soldered to the board, and some have a slot that only fits a single drive type. Check your laptop's manual or the maker's support page for the drive type and slot length before you buy.
What do I do with the old drive?
Keep it as a backup until you are sure the new SSD holds everything you need. After that, wipe it with your OS's disk tool before you give it away or recycle it, so your files do not go with it.




