Amazon Black Friday Week deals

Paid link

Storage · How-to guide

How to Install an SSD in a PC

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To install an SSD in a PC, shut the PC down, unplug it, and mount the 2.5-inch SATA drive in a drive bay, then connect a SATA data cable and a SATA power connector. Back up your files, and check the maker's manual for the bay location and the drive type your PC takes. After the drive is in, install the operating system or restore your backup.

  1. Back up your files before you start

    Copy your files to an external drive or cloud storage before you open the PC, so nothing is lost if the old drive fails during the swap. Decide whether to clone the old drive onto the SSD or install the operating system fresh and move your files back by hand. Cloning keeps your programs and settings in place, while a fresh install starts clean and takes longer to set up.

  2. Check which drive your PC takes

    The drives in this guide are 2.5-inch SATA drives, and your PC needs a bay that fits that size plus a SATA data cable and a SATA power connector. Look inside a desktop case for a spare bay and spare connectors before you buy anything. For a laptop, open the maker's manual and check the drive type, the bay location, and whether opening the laptop affects the warranty.

  3. Shut down, unplug, and open the case

    Shut the PC down and unplug it from the wall before you touch anything inside. Press the power button after unplugging to drain leftover charge, then remove the side panel on a desktop or the bottom panel on a laptop as the maker's manual shows. Touch a bare metal part of the case now and then to discharge static, and keep the screws in a small tray so they do not roll away.

  4. Mount the drive and connect the cables

    Slide the SSD into the bay or fasten it to the mounting bracket with the screws that came with the case or the drive, with the connectors facing the cables. Push the SATA data cable onto the drive and the matching port on the board, then push a SATA power connector from the power supply onto the drive until it sits flat. Press each plug in firmly and give each cable a gentle tug to check it is seated.

  5. Set up the new drive

    Start the PC and open the system settings or the startup screen to confirm the SSD is listed. If you cloned the old drive, the PC should start from the SSD; if you installed fresh, install the operating system and then move your files back from the backup. Leave the old drive out until the new setup runs as expected, so you still have a copy of your files.

What you need

PNY CS900 500GB 2.5" SATA III Internal

PNY CS900 500GB 2.5" SATA III Internal

A 500 GB 2.5-inch SATA III drive with read speeds up to 550 MB/s and a 3 year warranty, for a laptop or desktop upgrade.

View on Amazon
SanDisk SSD Plus

SanDisk SSD Plus

A 500 GB 2.5-inch SATA III drive with read speeds up to 545 MB/s, a 7 mm form factor, and a 3 year limited warranty.

View on Amazon
PNY CS900 250GB 2.5" SATA III Internal

PNY CS900 250GB 2.5" SATA III Internal

A 250 GB 2.5-inch SATA III drive with read speeds up to 535 MB/s and a 3 year warranty, for a smaller everyday upgrade.

View on Amazon
Kingston 960GB A400 SATA3 2.5" Internal SSD

Kingston 960GB A400 SATA3 2.5" Internal SSD

A 960 GB 2.5-inch SATA3 drive with a limited 3 year warranty, for a hard drive replacement with room for applications.

View on Amazon

These come from our ranked list Best Internal SATA SSD, which compares them spec by spec.

FAQ

Do I need a new SATA cable for the SSD?

A desktop install needs a SATA data cable and a SATA power connector. Check inside the case for spare cables and connectors before buying a cable. A laptop uses a connector built into the drive bay, so no cable is needed there.

Can I install an SSD in a laptop?

Many laptops take a 2.5-inch SATA drive in a bay under a bottom panel. Check the maker's manual for the drive type, the bay location, and whether opening the laptop affects the warranty. If the manual shows no drive bay, contact the maker rather than forcing the case open.

What do I do after the SSD is installed?

Confirm the SSD is listed in the system settings, then install the operating system or restore your backup. Move your files back and check that your programs and documents open as expected. Keep the old drive aside until the new setup runs well, so your files still have a copy.

Ranked internal ssds guides