Amazon Black Friday Week deals

Paid link

Storage · How-to guide

How to Install an Extra SSD in a PC

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To install an extra SSD in a PC, mount the drive in a free bay, connect a SATA data cable and a SATA power cable, then format it so the PC can use it. The drives below are 2.5 inch SATA drives, so they fit a spare bay and use the same two cables. Shut the PC down and unplug it before you open the case.

  1. Check for a spare bay and SATA port

    Open your PC manual and look for a free 2.5 inch drive bay and a spare SATA port on the motherboard. The manual also shows where the bays sit and which SATA ports are free. If the bays are already in use, check the manual for a mounting point on the case floor or behind the motherboard tray, and follow what the manual says.

  2. Shut down and open the case

    Shut the PC down and unplug the power cable before you touch anything inside. Open the side panel the way your PC manual shows, and set the panel aside. Work on a clear table with room to reach the drive bays, and keep the screws from the panel where you can find them again.

  3. Mount the drive in the bay

    Slide the SSD into the free 2.5 inch bay and line up the screw holes on the drive with the holes in the bay or tray. Fasten it with the screws that came with the case or the drive, and make sure it sits flat and does not move. A drive that wobbles can pull on its cables, so check that it feels firm before you move on.

  4. Connect the SATA data and power cables

    Push a SATA data cable into the small connector on the back of the drive, then push the other end into a free SATA port on the motherboard. Then push a SATA power cable from the power supply into the wider connector on the drive. Both plugs fit one way only, so line up the key and press gently until each plug sits flush.

  5. Format the drive before you use it

    Close the case, plug the PC back in and switch it on. Open the disk tool in your operating system and find the new drive, which appears unformatted. Create a volume on it and format it, then give it a drive letter or name. Once it shows up with free space, you can move files onto it or install apps there.

What you need

PNY CS900 500GB 2.5" SATA III Internal

PNY CS900 500GB 2.5" SATA III Internal

A 500 GB 2.5 inch SATA III drive with read speeds of up to 550 MB/s and write speeds of up to 500 MB/s with a 3 year warranty.

View on Amazon
SanDisk SSD Plus

SanDisk SSD Plus

A 500 GB 2.5 inch SATA III drive with read speeds of up to 545 MB/s and a 3 year limited warranty.

View on Amazon
PNY CS900 250GB 2.5" SATA III Internal

PNY CS900 250GB 2.5" SATA III Internal

A 250 GB 2.5 inch SATA III drive with read speeds of up to 535 MB/s and write speeds of up to 500 MB/s, with a 3 year warranty.

View on Amazon
Kingston 960GB A400 SATA3 2.5" Internal SSD

Kingston 960GB A400 SATA3 2.5" Internal SSD

A 960 GB 2.5 inch SATA3 drive with a limited 3 year warranty, listed as a hard drive replacement.

View on Amazon

These come from our ranked list Best Internal SATA SSD, which compares them spec by spec.

FAQ

Can I install an SSD without removing the old drive?

Yes. An extra SSD works next to the drive you already have, as long as your PC has a free bay and a spare SATA port. Your old drive stays untouched, and the new drive shows up as extra space once you format it.

Does the new SSD need a SATA cable?

Yes. A 2.5 inch SATA drive connects with a SATA data cable to the motherboard and a SATA power cable from the power supply. Check whether your PC came with spare cables, since some cases include them and some do not.

Will the PC boot from the new SSD?

Not on its own. A new drive is blank, so the PC keeps starting from the drive that already holds your operating system. To start from the new drive you would move the operating system onto it, which is a separate job.

Ranked internal ssds guides