Amazon Black Friday Week deals

Paid link

Storage · How-to guide

How to Connect an M.2 SSD to a PC

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To connect an M.2 SSD to a PC, fit the drive into a free M.2 slot on the motherboard, fasten it with the slot's screw, then set it up after the PC starts. Check your motherboard manual first to confirm the slot's keying, lengths and whether it takes SATA or NVMe drives.

  1. Check your motherboard manual first

    Find the M.2 slot in your motherboard manual and note its keying, the drive lengths it accepts and whether it takes SATA or NVMe drives, since a drive that does not match the slot will not fit or will not be detected. Note where the mounting screw and standoff sit, and whether your board shares the slot with other ports that switch off when the slot is used. If the manual shows no M.2 slot, plan for a 2.5-inch SATA drive and a SATA data cable instead.

  2. Shut down and open the case

    Shut the PC down, unplug the power cable and press the power button once to drain remaining power. Follow the maker's manual to remove the side panel, then touch a bare metal part of the case to discharge static before you handle the drive. Work on a clear surface with the case lying flat, keep the mounting screw where you can find it, and do not open a power supply or a battery compartment; contact the maker for those parts.

  3. Fit the drive into the slot

    Hold the drive by its edges and line up the notch on its connector with the key in the slot. Push it in at a slight angle until the connector is seated, then press the far end down toward the standoff and fasten it with the mounting screw. Do not force the drive or bend it, and do not tighten the screw past snug. If the drive will not sit flat, lift it out and check the notch against the slot key again.

  4. Close up and check the drive

    Refit the side panel, plug the power cable back in and start the PC. Enter the BIOS or UEFI setup to confirm the drive appears, then start your operating system and open the disk utility to initialize the drive and create a volume if it is new. If the drive does not appear, shut down, unplug the PC and reseat the drive before checking the manual again.

  5. Connect a SATA drive instead

    If every M.2 slot on your PC is already in use, a 2.5-inch SATA SSD is the other way to add storage. Mount the drive in a drive bay, connect a SATA data cable from the drive to a SATA port on the motherboard and a SATA power cable from the power supply, then start the PC and check that the drive appears. The picks below are 2.5-inch SATA drives for this route.

What you need

PNY CS900 500GB 2.5" SATA III Internal

PNY CS900 500GB 2.5" SATA III Internal

A 500 GB 2.5-inch SATA III SSD rated at up to 550 MB/s read and 500 MB/s write, with a 3 year warranty.

View on Amazon
SanDisk SSD Plus

SanDisk SSD Plus

A 500 GB 2.5-inch 7 mm SATA III 6 Gb/s SSD rated at up to 545 MB/s read, with a 3 year limited warranty.

View on Amazon
PNY CS900 250GB 2.5" SATA III Internal

PNY CS900 250GB 2.5" SATA III Internal

A 250 GB 2.5-inch SATA III SSD rated at up to 535 MB/s read and 500 MB/s write, with a 3 year warranty.

View on Amazon
Kingston 960GB A400 SATA3 2.5" Internal SSD

Kingston 960GB A400 SATA3 2.5" Internal SSD

A 960 GB 2.5-inch SATA3 SSD with a limited 3 year warranty, built as a hard drive replacement.

View on Amazon

These come from our ranked list Best Internal SATA SSD, which compares them spec by spec.

FAQ

How do I know if my PC has an M.2 slot?

Check your motherboard or laptop manual for an M.2 slot entry, or look for a short slot on the motherboard with a mounting screw and standoff at one end. The manual also states whether the slot takes SATA or NVMe drives.

Why does my new M.2 SSD not show up?

Shut the PC down, unplug it and reseat the drive so the connector is fully seated and the screw holds it flat. Then check the BIOS or UEFI setup and your disk utility to confirm the drive is detected and initialized.

Can I connect an M.2 SSD with a cable instead?

An M.2 drive fits into an M.2 slot on the motherboard, not onto a cable. If every M.2 slot on your PC is already in use, use a 2.5-inch SATA SSD with a SATA data cable and a SATA power cable.

Ranked internal ssds guides