Amazon Black Friday Week deals

Paid link

Storage · How-to guide

How to Attach a Heatsink to an SSD

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

A heatsink attaches to an SSD with a thermal pad between the drive and the metal heatsink, held in place by screws or clips. First check that the heatsink matches your SSD's form factor: the 2.5-inch SATA drives here install in a drive bay, while a stick heatsink fits a flat SSD that mounts on the motherboard. Shut the computer down and unplug it before you open the case.

  1. Check the heatsink fits your SSD

    Start with the form factor. A heatsink made for a flat SSD that mounts on the motherboard will not fit a 2.5-inch SATA drive, and a heatsink made for a 2.5-inch drive will not fit a flat one. Read the heatsink's packaging or instructions for the form factors it fits, then check your SSD's manual for its form factor. The four drives shown here are 2.5-inch SATA drives: the PNY CS900 at 500GB, the SanDisk SSD Plus at 500GB, the PNY CS900 at 250GB, and the Kingston A400 at 960GB. Buy the heatsink only after the two match.

  2. Shut down and unplug the computer

    Shut the computer down, unplug it from the wall, and follow the maker's manual for opening the case. Do not open a computer that is still under warranty without checking the maker's terms first; contact the maker if opening it would void the cover. Work on a clear, dry surface with the case on its side so the SSD stays still while you fit the heatsink.

  3. Clean the SSD before you fit the heatsink

    Wipe the top of the SSD with a dry, lint-free cloth so dust and fingerprints do not sit between the drive and the thermal pad. If the SSD has a paper sticker on the side the heatsink covers, leave the sticker in place unless the heatsink's instructions say to remove it. Do not use liquids or household cleaners on the drive. A clean, dry surface helps the thermal pad grip the drive.

  4. Place the thermal pad and seat the heatsink

    Peel the backing from the thermal pad and lay the pad flat on the SSD, covering the chips the heatsink will sit over. Line the heatsink up with the pad so it sits flat, then press it down evenly with your fingers. Do not slide the heatsink across the pad once it touches, since sliding can tear the pad or leave gaps. Check from the side that the heatsink sits flat against the pad with no corner lifted.

  5. Fasten the heatsink and check the drive

    Fasten the heatsink with the screws or clips that came with it, tightening each one a little at a time so the pressure stays even. Do not force a screw that will not turn; back it out and line the holes up again. Close the case, plug the computer in, and start it up. Open your system settings or the drive's own software to check that the SSD shows up with its full capacity: 500GB, 250GB, or 960GB for the drives shown here.

What you need

PNY CS900 500GB 2.5" SATA III Internal

PNY CS900 500GB 2.5" SATA III Internal

A 500GB 2.5-inch SATA III SSD with read speeds of up to 550MB/s and write speeds of up to 500MB/s.

View on Amazon
SanDisk SSD Plus

SanDisk SSD Plus

A 500GB 2.5-inch, 7mm SATA III SSD with read speeds of up to 545MB/s and write speeds of up to 505MB/s.

View on Amazon
PNY CS900 250GB 2.5" SATA III Internal

PNY CS900 250GB 2.5" SATA III Internal

A 250GB 2.5-inch SATA III SSD with read speeds of up to 535MB/s and write speeds of up to 500MB/s.

View on Amazon
Kingston 960GB A400 SATA3 2.5" Internal SSD

Kingston 960GB A400 SATA3 2.5" Internal SSD

A 960GB 2.5-inch SATA3 SSD for fast start up, loading and file transfers.

View on Amazon

These come from our ranked list Best Internal SATA SSD, which compares them spec by spec.

FAQ

Can I put a heatsink on a 2.5-inch SATA SSD?

A stick heatsink is made for a flat SSD that mounts on the motherboard, not for a 2.5-inch SATA drive in a bay. The 2.5-inch drives shown here install in a drive bay with a SATA cable, so check your SSD's form factor before you buy a heatsink.

Do I need to remove the SSD's sticker first?

Leave the paper sticker in place unless the heatsink's instructions say to remove it. The sticker protects the drive's surface, and peeling it off can leave residue that keeps the thermal pad from sitting flat.

What if the SSD does not show up after I fit the heatsink?

Shut the computer down and unplug it, then open the case and check that the drive's cables are seated and the heatsink is not pressing on anything else. Follow the maker's manual for your computer and the SSD, and contact the maker if the drive still does not show up.

Ranked internal ssds guides