Amazon Black Friday Week deals

Paid link

PC Components · How-to guide

How to Apply Thermal Paste to a CPU

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

Thermal paste fills the tiny gaps between the CPU and the cooler so heat moves from one to the other. Put a small dot in the center of the CPU, then press the cooler down and tighten it, and the pressure spreads the paste into a thin layer. Shut the PC down and unplug it before you open the case.

  1. Check the cooler fits the socket and the case

    Check the socket first: the ARCTIC coolers fit LGA1851, LGA1700, AM4 and AM5, the Thermalright fits AM4 and AM5 and Intel LGA 1700, 1150, 1151, 1200 and 1851, and the LIAN LI fits LGA 1851 and 1700 and AMD AM5 and AM4. Check the size too: the Thermalright measures 4.92x5.31x6.1 inch, and the LIAN LI radiator measures 400 by 122 by 24 mm. Check your case and motherboard for compatibility with the cooler size before you start.

  2. Shut down and unplug the PC

    Shut the PC down and unplug it before you open the case, and follow the maker's manual for your cooler. Work on a clear desk with the case on its side so the motherboard faces up. Keep the screws and the mounting parts together as you take them out, so nothing gets lost before the cooler goes back on.

  3. Clean the old paste off

    Take the cooler off the CPU and wipe the old paste off the CPU and the cooler base with a lint-free cloth. Keep wiping until both surfaces look clean, and let them dry before you apply new paste. Old paste left under new paste leaves gaps, and gaps stop the heat moving from the CPU to the cooler.

  4. Put a small dot in the center

    Put a dot of paste about the size of a pea in the center of the CPU. Do not spread it with a finger or a card, and do not add a second dot. The pressure from the cooler spreads the dot into a thin layer when you mount the cooler, and a thin layer covers the CPU without squeezing out at the edges.

  5. Mount the cooler and connect the fans

    Set the cooler down on the CPU and tighten the screws a little at a time in turn, following the maker's manual, until the cooler sits flat. The ARCTIC coolers shift the cold plate center toward the CPU hotspot, and the Thermalright uses metal fasteners for Intel and AMD platforms. Connect the fan cables: the ARCTIC coolers route the radiator fan cables through the hose sheathing, so only a single visible cable reaches the motherboard.

What you need

ARCTIC Liquid Freezer III Pro 360 A-RGB

ARCTIC Liquid Freezer III Pro 360 A-RGB

A 360 mm AIO cooler for LGA1851, LGA1700, AM4 and AM5 with a contact frame, an integrated VRM fan and a 6-year warranty.

View on Amazon
Thermalright Peerless Assassin 120 SE CPU Cooler

Thermalright Peerless Assassin 120 SE CPU Cooler

An air cooler with 6 heat pipes and dual 120 mm PWM fans at 1550 RPM, for AM4, AM5 and Intel LGA 1700, 1150, 1151, 1200 and 1851.

View on Amazon
ARCTIC Liquid Freezer III Pro 360

ARCTIC Liquid Freezer III Pro 360

A 360 mm AIO cooler with 3 120 mm fans, a contact frame and an integrated VRM fan, for LGA1851, LGA1700, AM4 and AM5.

View on Amazon
LIAN LI HydroShift II Curved 360 TL Flex AIO Cooler-Black-HS2OLDC36TB

LIAN LI HydroShift II Curved 360 TL Flex AIO Cooler-Black-HS2OLDC36TB

A 360 mm AIO cooler with a 6.67-inch 2K OLED display, 3 120 mm fans at up to 2600 RPM and a 400 by 122 by 24 mm radiator.

View on Amazon

These come from our ranked list Best Cooler for PC, which compares them spec by spec.

FAQ

How much thermal paste should I use?

A small dot in the center of the CPU is enough. The pressure from the cooler spreads it into a thin layer when you mount the cooler, so do not spread it by hand and do not add more.

Do I need to remove the old thermal paste first?

Yes. Wipe the old paste off the CPU and the cooler base with a lint-free cloth before you apply new paste, and let both surfaces dry. Old paste left under new paste leaves gaps that stop heat moving.

Can I reuse thermal paste after removing the cooler?

No. Once the cooler comes off, the paste layer breaks, so clean both surfaces and apply a fresh dot before you mount the cooler again.

What happens if I use too much thermal paste?

Excess paste squeezes out from under the cooler and can spread onto the motherboard. Wipe away any paste that squeezes out, and use a smaller dot next time.

Ranked cpu coolers guides