How to Apply Liquid Metal to a CPU
Liquid metal is a thermal paste alternative that sits between the CPU and the cooler and moves heat from the chip to the cooler. You spread a thin, even layer across the top of the CPU, then fit the cooler back on top of it. The steps below cover shutting the PC down, cleaning the old paste off, applying the liquid metal and checking the result.
Shut the PC down and unplug it
Shut the PC down through the operating system, then unplug the power cable from the wall and from the back of the case. Follow the maker's manual for your PC or motherboard before you open anything, and leave the parts to cool if the PC was running. Touch a bare metal part of the case first to discharge static, and keep the case on a flat, dry surface with good light while you work.
Remove the cooler and clean the CPU
Loosen the cooler fixings a little at a time, following the order in the cooler manual, then lift the cooler straight off the CPU. Wipe the old paste off the top of the CPU with a lint-free cloth, then clean the surface with a little isopropyl alcohol on a fresh cloth until no residue remains. Do the same for the base of the cooler, and let both surfaces dry before you go on.
Check the cooler surface and the board
Liquid metal is electrically conductive, so keep it on the top of the CPU and away from the motherboard, the socket and any nearby parts. Check the cooler manual to confirm the surface that touches the CPU suits liquid metal, and do not use it on a bare aluminium surface, which it can damage. If you are unsure about the material, use the paste the cooler maker supplies instead.
Spread a thin, even layer
Put a small amount of liquid metal in the centre of the CPU, then spread it with the applicator or brush that comes with it until the whole top of the CPU has a thin, even coat. Work slowly so none runs over the edge of the CPU, and wipe up any drop at once with a lint-free cloth. The layer should look smooth and unbroken, with no bare patches and no pools at the sides.
Fit the cooler and check the result
Lower the cooler onto the CPU without sliding it, then tighten the fixings a little at a time in the order the cooler manual gives so the pressure stays even. Plug the fan and pump cables back in, close the case and reconnect the power cable. Switch the PC on and watch the CPU temperature in the maker's software while it idles, then open the case again later to check the layer has stayed in place.
What you need

ARCTIC Liquid Freezer III Pro 360 A-RGB
An AIO cooler for LGA1851, LGA1700, AM4 and AM5 with P12 PRO fans, a contact frame for Intel sockets and a 6-year warranty.
View on Amazon
ARCTIC Liquid Freezer III Pro 360
An AIO cooler with three 120 mm fans for LGA1851, LGA1700, AM4 and AM5, with a contact frame for Intel sockets and a 6-year warranty.
View on Amazon
Thermalright Aqua Elite 120 V3 AIO CPU Cooler
A 120 mm AIO cooler with two ARGB fans and a fourth-generation pump head, with lighting that syncs with the motherboard.
View on Amazon
Thermalright Aqua Elite 240 V3 Water Cooling CPU Cooler
A 240 mm AIO cooler with two PWM ARGB fans, S-FDB bearings and an efficient PWM-controlled pump.
View on AmazonThese come from our ranked list Best CPU Liquid Cooler, which compares them spec by spec.
FAQ
Can liquid metal damage a CPU or motherboard?
Yes, if it spills. Liquid metal conducts electricity, so a drop on the board or in the socket can short parts. Keep it on the top of the CPU only, wipe up spills at once, and follow the maker's manual.
How do I remove liquid metal from a CPU?
Shut the PC down, unplug it and remove the cooler, then wipe the liquid metal off with a lint-free cloth. Clean the surface with a little isopropyl alcohol on a fresh cloth until it is bare, and let it dry before you apply paste or fit the cooler again.
How often should I reapply liquid metal?
There is no fixed interval. Watch for signs such as higher CPU temperatures under load than before, or a patchy layer when you next open the PC, and reapply when you see them.




