How to Add a SATA SSD
Adding a SATA SSD means fitting a 2.5-inch drive into a drive bay or slot, connecting it with a SATA data cable and a SATA power cable from the power supply, then setting it up in the operating system. The drive can hold the operating system or serve as extra storage. The steps below cover checking the fit, fitting the drive, connecting the cables and preparing it for use.
Shut the PC down and unplug it
Shut the PC down through the operating system, then unplug the power cable from the wall and from the back of the case. Follow the maker's manual for your PC or motherboard before you open anything, and leave the parts to cool if the PC was running. Touch a bare metal part of the case first to discharge static, and keep the case on a flat, dry surface with good light while you work.
Check the bay and the cables
Look for a free 2.5-inch drive bay or mounting point inside the case, and check the maker's manual for where it sits. Find a SATA data cable and a spare SATA power connector from the power supply, and confirm the motherboard has a free SATA port. Check the maker's manual for how the drive is held in place in your case and its bay layout.
Fit the drive into the bay
Slide the SSD into the drive bay or fasten it to the mounting point with the screws or tool-free clips the case provides, keeping the SATA connectors facing the motherboard. Do not force the drive into place, and leave it level so the connectors line up. Check that the drive sits firmly and does not move when you nudge it.
Connect the data and power cables
Push the SATA data cable onto the small connector on the drive, then push the other end onto a SATA port on the motherboard. Push the SATA power connector from the power supply onto the wider connector on the drive until it sits fully home. Both connectors fit one way only, so turn a plug around rather than forcing it.
Set the drive up in the operating system
Close the case, plug the power cable back in and switch the PC on. Open the disk management tool in your operating system and check that the new drive appears in the list. Create a partition on the drive and format it, following the prompts, then give it a drive letter or mount point so it shows up with your other storage.
What you need

PNY CS900 500GB 2.5" SATA III Internal
A 500 GB 2.5-inch SATA III SSD with rated read speeds up to 550 MB/s and a 3-year warranty.
View on Amazon
SanDisk SSD Plus
A 500 GB 2.5-inch SATA III SSD with read speeds up to 545 MB/s, a 7 mm form factor and a 3-year limited warranty.
View on Amazon
PNY CS900 250GB 2.5" SATA III Internal
A 250 GB 2.5-inch SATA III SSD with rated read speeds up to 535 MB/s and a 3-year warranty.
View on Amazon
Kingston 960GB A400 SATA3 2.5" Internal SSD
A 960 GB 2.5-inch SATA3 SSD for fast start-up, loading and file transfers, with a limited 3-year warranty.
View on AmazonThese come from our ranked list Best Internal SATA SSD, which compares them spec by spec.
FAQ
Can I add a SATA SSD to a laptop?
It depends on the laptop. Check the maker's manual for a free 2.5-inch bay or a SATA slot, since slim laptops use different layouts inside. A free bay and a SATA slot mean the drive fits inside the laptop.
Do I need to reinstall the operating system?
No, if the SSD is extra storage. You only reinstall the operating system when you want the SSD to hold it, and the maker's manual covers moving it. A new drive used for files just needs a partition and a format.
What if the drive does not show up?
Check the cables first. Open the case with the PC shut down and unplugged, and push both the SATA data and power connectors fully home. Then check the disk management tool again, and check the maker's manual if the drive still does not appear.




