How to Mount a GPU Sideways
To mount a GPU sideways, fit a vertical mount bracket in the case and connect the card to the motherboard with a PCIe riser cable, so the card sits parallel to the motherboard with its fans facing the side panel. Check the case manual for a vertical mount slot and the riser cable length before you buy the bracket.
Check the case takes a vertical mount
Look at the back of the case for vertical slot covers beside the normal horizontal slots, and check the case manual for the bracket size and the riser cable length it takes. Measure the space between the motherboard and the side panel so the card, its fans and its power cables clear the panel when the case is closed. Use a case with vertical slots for the bracket, or fit a bracket kit made for that case.
Shut the PC down and unplug it
Shut the PC down through the operating system, then switch off the power supply and unplug the power cable from the wall. Follow the case manual for removing the side panel, and leave the PC unplugged while you work inside it. Keep the screws from the panel in a small tray so they are easy to find when you close the case.
Fit the bracket and riser cable
Remove the vertical slot covers at the back of the case and fix the vertical mount bracket in their place, following the steps in the bracket manual. Plug the riser cable into the motherboard PCIe slot and fasten its other end to the bracket, keeping the cable flat with no sharp bends. Tighten the bracket screws until the bracket sits firm and does not move when you push it.
Seat the card in the riser
Line up the card with the connector on the riser cable and press it in until it sits fully in the slot. Fasten the card to the bracket with the screws from the bracket kit, then plug in the power cables from the power supply, matching each plug to the socket on the card. Check that the card sits straight and clear of the side panel before you close the case.
Check the card is seen and its fans spin
Close the side panel, plug the power cable back in and switch the PC on. Check that the screen shows a picture and that the card shows up in the system settings, and look through the side panel to see that the fans spin. If the screen stays blank, shut the PC down, unplug it and reseat the riser cable, then check the motherboard manual for the PCIe slot setting.
What you need

ASUS PRIME GeForce RTX 5060 Ti 16GB
An ASUS GeForce RTX 5060 Ti with 16 GB of GDDR7 memory, a 2.5-slot design, PCIe 5.0 and Axial-tech fans, weighing 3.2 lb.
View on Amazon
ASUS Prime GeForce RTX 5060 Ti 8GB
An ASUS GeForce RTX 5060 Ti with 8 GB of GDDR7 memory, a 2.5-slot design, PCIe 5.0 and Axial-tech fans, weighing 2.65 lb.
View on Amazon
MSI Gaming RTX 3050 LP 6G OC Graphics Card
An MSI GeForce RTX 3050 with 6 GB of GDDR6 memory, HDMI and DisplayPort outputs, weighing 1.16 lb.
View on Amazon
NVIDIA RTX 4000 SFF Ada Generation Workstation Ada Lovelace Architecture Dual Slot Low Profile Professional Graphics Board 900-5G192-2571-000 VD8465
An NVIDIA RTX 4000 SFF Ada Generation workstation card with a dual-slot low-profile board for small-form-factor builds.
View on AmazonThese come from our ranked list Best Sff GPU, which compares them spec by spec.
FAQ
Does a vertical GPU mount hurt performance?
A riser cable can slow the PCIe link if the cable runs at an older PCIe version than the motherboard and the card. Check the PCIe version of the riser cable and the motherboard manual, and match them before you buy.
Will any case fit a vertical GPU mount?
No. The case needs vertical slot covers at the back and room between the motherboard and the side panel for the card and its fans. Check the case manual for the vertical mount kit and the bracket size it takes.
Does a sideways GPU run hotter?
It can, since the fans sit close to the side panel and pull in less air. Leave a gap between the card and the panel, and check the card temperatures in the software you already use. If the card runs hot, move it back to the standard horizontal slot.




