How to Connect a Graphics Card to a PC
To connect a graphics card to a PC, shut the computer down, unplug it, seat the card in a PCIe slot on the motherboard, secure the bracket, connect the monitor cable to the card, and then plug the computer back in. Check the slot, the space in the case and the monitor ports before you start, and follow the maker's manual for your card and your computer.
Shut down and unplug first
Shut the computer down and unplug it before you open it, and follow the maker's manual for your computer and your card. Remove the side panel as the manual shows, and touch a metal part of the case to discharge static before you handle the card. Work on a clear, flat surface with the computer lying on its side if the manual shows that position. Do not open a computer that is under warranty for this work; contact the maker instead.
Check the slot and the space
Find the PCIe slot on the motherboard that the maker's manual names for the graphics card, and check that the slot is free. Check the space in the case against the card: the two ASUS cards use a 2.5-slot design, and the MSI and NVIDIA cards are low-profile boards. The ASUS cards are also SFF-Ready, which suits a small case. Remove the slot covers from the case for the slots the card will cover, as the manual shows.
Seat the card in the slot
Hold the card by its edges and line up its connector with the PCIe slot, then press it straight down until it sits fully in the slot. The card should sit level, with its bracket lined up with the case. Secure the bracket to the case as the manual shows, so the card does not move when you connect cables. If the card does not sit level, lift it out and line it up again instead of forcing it.
Connect the monitor to the card
Connect the monitor cable to a port on the graphics card, not to a port on the motherboard, so the monitor uses the new card. The ASUS cards have HDMI and DP 2.1 ports, and the MSI card has one DisplayPort and two HDMI 2.1a ports. Check that the cable matches the port on the card and the port on the monitor. If the monitor stays blank after you plug the computer back in, check the cable and the input the monitor is set to.
Plug back in and check the picture
Put the side panel back on as the manual shows, then plug the computer back in and turn it on. The monitor should show a picture through the cable you connected to the card. If the picture does not appear, shut the computer down, unplug it, and check that the card sits fully in the slot and the cable sits fully in its port. Follow the maker's manual for any further steps.
What you need

ASUS PRIME GeForce RTX 5060 Ti 16GB
A 16GB GDDR7 graphics card with PCIe 5.0, HDMI and DP 2.1 ports, a 2.5-slot design and dual BIOS.
View on Amazon
ASUS Prime GeForce RTX 5060 Ti 8GB
An 8GB GDDR7 graphics card with PCIe 5.0, HDMI and DP 2.1 ports, a 2.5-slot design and dual BIOS.
View on Amazon
MSI Gaming RTX 3050 LP 6G OC Graphics Card
A 6GB GDDR6 graphics card with one DisplayPort and two HDMI 2.1a ports, a 1492 MHz boost clock and a low-profile board.
View on Amazon
NVIDIA RTX 4000 SFF Ada Generation Workstation Ada Lovelace Architecture Dual Slot Low Profile Professional Graphics Board 900-5G192-2571-000 VD8465
A dual-slot low-profile professional graphics board with Ada Lovelace architecture.
View on AmazonThese come from our ranked list Best Sff GPU, which compares them spec by spec.
FAQ
Do I plug the monitor into the graphics card or the motherboard?
Plug it into the graphics card. A cable on the motherboard leaves the card unused, since the monitor then takes its picture from the motherboard instead of the card.
What if the card does not fit in my case?
Check the card against the space in the case before you buy it. The two ASUS cards use a 2.5-slot design, the MSI and NVIDIA cards are low-profile boards, and the ASUS cards are SFF-Ready for a small case. Measure the space in your case and compare it with the card's size in its manual.
Do I need to remove an old graphics card first?
Yes, if a card already sits in the slot you need, remove it first. Shut the computer down, unplug it, remove the bracket screw as the manual shows, and lift the old card straight out of the slot. Follow the maker's manual for your computer and your card.




