How to Build Your First PC
Building your first PC means choosing parts that fit together, putting them in a case with room for them, and connecting power before you install the operating system. Start with the motherboard size, the graphics card length and the cooler size, then pick a case that takes them all. The steps below follow that order.
Pick parts that fit together
Start with the motherboard, since the case must take its size. The Lian Li A3-mATX takes mATX and ITX boards with 4 expansion slots, while the Lian Li A4-H2OX5, the Fractal Design Terra Jade and the Cooler Master NR200P V3 take Mini-ITX boards only. Check the graphics card length against the case: the A3-mATX takes cards up to 415mm, the NR200P V3 up to 361.5mm and the Terra Jade up to 322mm. Check the cooler too: the A3-mATX takes a 360mm radiator, and the A4-H2OX5 takes a 240mm AIO. Match the power supply to the case: the A3-mATX takes ATX, SFX and SFX-L units, while the NR200P V3 takes SFX units up to 130mm.
Lay out the parts and the case
Set the case on a clear desk and open the side panel. Lay out the motherboard, cooler, graphics card, power supply, memory and storage where you can reach them, with the screws and the manual for each part nearby. Read the manual for the case and the motherboard before you fit anything, since the manual shows where each part mounts and which cables go where. Touch the metal of the case before you handle parts, and work with the power supply unplugged.
Install the motherboard and cooler
Fit the motherboard into the case first, then the cooler. Line up the board with the mounting points in the case and fasten it with the screws from the case. Mount the cooler over the processor following the cooler manual, and check that it clears the memory and the side panel. The A3-mATX takes a 360mm radiator, the A4-H2OX5 takes a 240mm AIO, and the NR200P V3 takes top-mounted 240mm or 280mm radiators. Check the cooler height and the radiator size against the case before you buy.
Fit the graphics card and power supply
Slide the graphics card into its slot on the motherboard and fasten it to the case. The A3-mATX takes cards up to 415mm, the NR200P V3 takes cards up to 361.5mm on a vertical mount with a PCIe 5.0 riser cable, and the Terra Jade takes cards up to 322mm. The A4-H2OX5 mounts the card behind the motherboard on a PCIe 5.0 riser cable. Fit the power supply in its bay: the A3-mATX takes ATX, SFX and SFX-L units, the A4-H2OX5 takes SFX and SFX-L units, and the NR200P V3 takes SFX units up to 130mm.
Connect power and check the build
Connect the power cables to the motherboard, the graphics card and the storage, then connect the case cables for the power button and the front USB ports. The Terra Jade has a front USB Type-C port at 20Gbps, and the A3-mATX has steel mesh panels for airflow. Check every cable seats fully, close the side panel, then plug the power supply in and press the power button. If the screen stays dark, shut the PC down, unplug it, and check the cables and the card seating against the manual before you try again.
What you need

Lian Li A3-mATX PC Case
A 26.3L mATX case with room for a 415mm graphics card and a 360mm radiator, steel mesh panels and a walnut wood front.
View on Amazon
Lian Li A4-H2OX5 Mini-ITX Case-SFX Layout-PCIe 5.0 Riser-Black-A4H2OX5
An 11L Mini-ITX case with a triple-slot GPU mount, a 240mm AIO, a PCIe 5.0 riser and an aluminum exterior.
View on Amazon
Fractal Design Terra Jade
A 10.4L Mini-ITX case with room for a 322mm graphics card, a walnut front panel and a USB Type-C 20Gbps port.
View on Amazon
Cooler Master NR200P V3 Mini-ITX PC Case
An 18.6L Mini-ITX case with a 361.5mm vertical GPU mount, a PCIe 5.0 riser and room for 240mm or 280mm radiators.
View on AmazonThese come from our ranked list Best ITX Case, which compares them spec by spec.
FAQ
What size case do I need for a first build?
Match the case to the parts: the Lian Li A3-mATX takes mATX and ITX boards with cards up to 415mm, while the A4-H2OX5, Terra Jade and NR200P V3 take Mini-ITX boards only. The Terra Jade takes cards up to 322mm and the NR200P V3 up to 361.5mm.
How do I know if a graphics card fits the case?
Compare the card length in millimeters to the case GPU support: the A3-mATX takes cards up to 415mm, the NR200P V3 up to 361.5mm and the Terra Jade up to 322mm. The A4-H2OX5 mounts a triple-slot card behind the motherboard on a PCIe 5.0 riser. Check the length before you buy, since a longer card will not fit.
How do I keep a first build cool?
Use the airflow the case gives: the A3-mATX has steel mesh side and top panels, and the NR200P V3 has a vented mesh panel. The A3-mATX takes a 360mm radiator and up to 10 x 120mm fans, the A4-H2OX5 takes a 240mm AIO, and the NR200P V3 takes top-mounted 240mm or 280mm radiators. Fill the fan mounts and keep the vents clear.




