Amazon Black Friday Week deals

Paid link

PC Components · How-to guide

How to Wire a PC Power Supply

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

Wiring a PC power supply means running its cables from the unit to the motherboard, graphics card, drives and fans, with each cable matched to the socket it fits. Start with the PC shut down and unplugged, mount the unit in the case, then connect the motherboard, CPU power and graphics card cables before storage and case fans. Check that every plug is seated before you switch the PC on.

  1. Shut down and mount the unit

    Shut the PC down and unplug it from the wall before you touch anything inside the case. Slide the power supply into its bay at the bottom or top of the case and fasten it with the screws from the case or the unit, with the fan facing the vent or filter your case manual shows. Do not open the power supply itself; if it has a fault, contact the maker.

  2. Connect the motherboard and CPU cables

    Find the wide main power cable and push it into the matching socket on the edge of the motherboard until the clip clicks into place. Then find the CPU power cable and connect it to the socket near the top of the board, close to the processor. Route both cables behind the motherboard tray where the case allows, so they stay clear of fans and keep airflow open.

  3. Connect the graphics card cable

    If your graphics card has a 12V-2x6 socket, use the native 12V-2x6 cable from the power supply and push it straight into the card until it sits flush with no gap at the edge. A plug that is only partly seated can leave the card without power, so press it in firmly and check it from the side. Route the cable so it does not pull on the card or rest against a fan.

  4. Connect drives and case fans

    Connect a SATA power cable to each drive in the case, such as a solid-state drive or a hard drive, and to any other part that takes the same flat plug. Connect case fans to the fan headers on the motherboard or to the fan cables the case provides, following the labels on the board. Leave any cables your build does not need out of the case if the unit is fully modular.

  5. Check every plug before switching on

    Go through each cable once more and press every plug to make sure it is fully seated, with no connector hanging loose or half in its socket. Tidy the cables with ties or the case channels so nothing touches a fan blade. Plug the PC back in, switch the power supply on at its rear switch if it has one, then press the case power button and check that the fans spin and the screen shows a picture.

What you need

CORSAIR RM1000e ATX 3.1 PCIe 5.1 Ready 1000W Power Supply

CORSAIR RM1000e ATX 3.1 PCIe 5.1 Ready 1000W Power Supply

A 1000 W fully modular unit with a native 12V-2x6 cable included, a 120 mm rifle bearing fan and a 7-year manufacturer warranty.

View on Amazon
CORSAIR RM1000x ATX 3.1 PCIe 5.1 1000W Power Supply

CORSAIR RM1000x ATX 3.1 PCIe 5.1 1000W Power Supply

A 1000 W fully modular unit with a native 12V-2x6 connector, rated up to 91% efficiency and a 10-year manufacturer warranty.

View on Amazon
MSI MAG A850GL PCIE5

MSI MAG A850GL PCIE5

An 850 W fully modular unit, 80 PLUS Gold certified and ATX 3.1 and PCIe 5.1 ready, with a 10-year limited manufacturer warranty.

View on Amazon
Thermaltake Toughpower GT 850W ATX 3.1 Standard Power Supply

Thermaltake Toughpower GT 850W ATX 3.1 Standard Power Supply

An 850 W fully modular unit with 80 PLUS Gold efficiency, a native 12V-2x6 connector and Smart Zero Fan, with a 5-year manufacturer warranty.

View on Amazon

These come from our ranked list Best Power Supply, which compares them spec by spec.

FAQ

Do I need to connect every cable from the power supply?

No. With a fully modular unit you connect only the cables your build needs and leave the rest out of the case, which keeps the inside tidier and the air moving.

What if my graphics card shows no picture after wiring?

Shut the PC down and unplug it, then check that the graphics card cable and the motherboard cable are fully seated. Also check that the monitor cable is in the graphics card and not in the motherboard.

Can I open the power supply to fix it?

No. Do not open a power supply, and do not try to repair it yourself. If it has a fault or makes an odd noise, unplug it and contact the maker.

Ranked power supplies guides