Amazon Black Friday Week deals

Paid link

PC Components · How-to guide

How to Install a PSU in a PC

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To install a PSU, shut the PC down, unplug it, and remove the old unit and its cables. Mount the new power supply in the case, connect the motherboard, CPU, and graphics card cables, then plug the PC back in and power it on. Follow the maker's manual for your case and power supply at each step.

  1. Shut down and unplug the PC

    Shut the PC down through the operating system, then unplug the power cable from the wall and from the PC. Press the power button again to drain any charge left in the system, and move the case to a clear work surface. Read the maker's manual for your case and power supply before you open anything, and keep the screws you remove in one place.

  2. Remove the old power supply

    Open the case and unplug every cable from the old power supply, starting with the graphics card, then the motherboard and CPU cables, then any drive cables. Note where each cable was connected so you can match the new ones later. Unscrew the power supply from the back of the case and slide it out, taking care not to snag cables on the case edges.

  3. Mount the new power supply

    Slide the new power supply into the mounting bay at the back of the case and line up its screw holes with the case. Fasten it with the screws that came with the unit or the case, and check that it sits flat with no gap at the back panel. Follow the maker's manual for which way the fan faces, since some cases take air from below and others from inside the case.

  4. Connect the power cables

    Connect the main motherboard cable first, then the CPU cable, then the graphics card cable. If your power supply has a native 12V-2x6 cable, use it for the graphics card and push it in until it seats fully. Connect drive cables where your drives need them. With a fully modular unit, connect only the cables your build uses and leave the rest out of the case.

  5. Power on and check the PC

    Plug the power cable back in, switch the power supply on, and press the PC power button. Check that the fans spin and the PC reaches its normal startup screen. If nothing happens, switch off and unplug the PC, then check that the motherboard and CPU cables are seated fully before you try again.

What you need

CORSAIR RM1000e ATX 3.1 PCIe 5.1 Ready 1000W Power Supply

CORSAIR RM1000e ATX 3.1 PCIe 5.1 Ready 1000W Power Supply

A 1000W fully modular power supply, ATX 3.1 and PCIe 5.1 ready, with a native 12V-2x6 cable and a 7-year warranty.

View on Amazon
CORSAIR RM1000x ATX 3.1 PCIe 5.1 1000W Power Supply

CORSAIR RM1000x ATX 3.1 PCIe 5.1 1000W Power Supply

A 1000W fully modular power supply, ATX 3.1 and PCIe 5.1 ready, with a native 12V-2x6 connector and a 10-year warranty.

View on Amazon
MSI MAG A850GL PCIE5

MSI MAG A850GL PCIE5

An 850W fully modular power supply, 80 PLUS Gold, ATX 3.1 and PCIe 5.1 ready, with a native 12V-2x6 cable and a 10-year limited warranty.

View on Amazon
Thermaltake Toughpower GT 850W ATX 3.1 Standard Power Supply

Thermaltake Toughpower GT 850W ATX 3.1 Standard Power Supply

An 850W fully modular power supply, 80 PLUS Gold, ATX 3.1 and PCIe 5.1 ready, with Smart Zero Fan and a 5-year warranty.

View on Amazon

These come from our ranked list Best Power Supply, which compares them spec by spec.

FAQ

Can I reuse the cables from my old PSU?

Use the cables that came with the new power supply. Cables from another unit may not match its sockets, so follow the maker's manual and connect only the cables that came with the new unit.

Do I need to remove the old PSU first?

Yes. The old unit and its cables must come out before the new one goes in, since the case has one mounting bay and each cable plugs into the new unit. Keep the old unit aside until the new one runs.

What if the PC does not power on?

Switch off and unplug the PC, then check that the motherboard, CPU, and graphics card cables are seated fully and that the power supply switch is on. If it still does not start, check the maker's manual for the next steps.

Ranked power supplies guides