How to Use a Computer Power Supply
A computer power supply converts wall power into the power your PC parts use, and you use it by mounting it in the case, connecting its cables to each part, and switching it on. Connect only the cables your build needs, since all four supplies here are fully modular. Check the wattage and connector each part lists, and match them to the supply before you connect anything.
Check the wattage your parts list
Start with the power figures published for your parts. The graphics card and the processor list the power they draw, and the supply must cover the total for the whole build. The CORSAIR RM1000e and RM1000x are 1000W supplies, while the MSI MAG A850GL PCIE5 and the Thermaltake Toughpower GT 850W are 850W supplies. Compare the wattage figure on the supply with the figures published for your parts, and check the requirements published for your software or game before you choose. A supply that cannot cover the total leaves the build short of power.
Mount the supply in the case
Shut the computer down and unplug it before you open the case, and follow the steps in the maker's manual for your case and your supply. Set the supply in its bay as the case manual shows, then fasten it with the screws that came with the case. Keep the cables clear of the fan so air moves through the case. If the computer is still under warranty, check the warranty terms before you open it, and contact the maker if you are unsure.
Connect only the cables you need
These supplies are fully modular, so connect only the cables your build needs and leave the rest out of the case. Connect the main board cable to the board, the processor cable to the board, and the graphics card cable to the card. The CORSAIR RM1000e includes a native 12V-2x6 cable, the CORSAIR RM1000x has a native 12V-2x6 connector, and the MSI MAG A850GL PCIE5 includes a native dual-color 12V-2x6 cable. The Thermaltake Toughpower GT 850W has native PCIe 12V-2x6 connectors for modern graphics cards. Push each connector in until it seats, and check that the latch on the graphics card connector has caught.
Switch on and check the fan
With the cables connected, plug the computer in and switch the supply on at its rear switch. The Thermaltake Toughpower GT 850W uses Smart Zero Fan technology, which adjusts fan speed based on load to keep noise down during low-load work. The CORSAIR RM1000e uses a 120mm rifle bearing fan with a fan curve that keeps fan noise down at full load. Listen for the fan and check that the computer starts. If the computer does not start, switch it off, unplug it, and check each cable connection again before you contact the maker.
Read the efficiency rating
The efficiency rating says how much of the wall power reaches your parts as usable power. The MSI MAG A850GL PCIE5 and the Thermaltake Toughpower GT 850W are 80 PLUS Gold rated, and the Thermaltake gives up to 90% efficiency. The CORSAIR RM1000x is Cybenetics Gold certified and rated for up to 91% efficiency. The CORSAIR RM1000e is also Cybenetics Gold. Higher efficiency means less power lost as heat, so compare the rating and the efficiency figure when you choose between two supplies at the same wattage.
What you need

CORSAIR RM1000e ATX 3.1 PCIe 5.1 Ready 1000W Power Supply
A 1000W fully modular supply with a native 12V-2x6 cable, a 120mm rifle bearing fan and a 7-year manufacturer warranty.
View on Amazon
CORSAIR RM1000x ATX 3.1 PCIe 5.1 1000W Power Supply
A 1000W fully modular supply with a native 12V-2x6 connector, Cybenetics Gold certification and a 10-year manufacturer warranty.
View on Amazon
MSI MAG A850GL PCIE5
An 850W fully modular supply with 80 PLUS Gold certification, ATX 3.1 and PCIe 5.1 support and a 10-year limited warranty.
View on Amazon
Thermaltake Toughpower GT 850W ATX 3.1 Standard Power Supply
An 850W fully modular supply with 80 PLUS Gold efficiency, Smart Zero Fan and a native 450W PCIe 5.1 connector.
View on AmazonThese come from our ranked list Best Power Supply, which compares them spec by spec.
FAQ
Do I need a 1000W power supply?
It depends on the power figures published for your parts. Add the figures for the graphics card, the processor and the rest of the build, then compare the total with the wattage on the supply. Check the requirements published for your software or game before you choose.
What does fully modular mean?
It means every cable detaches from the supply, so you connect only the cables your build needs. All four supplies here are fully modular, which leaves the cables you do not use out of the case.
What is a 12V-2x6 connector for?
It is the connector for modern graphics cards. All four supplies here have a native 12V-2x6 cable or connector, so check that your graphics card takes that connector.




