Amazon Black Friday Week deals

Paid link

PC Components · How-to guide

How to Connect Power Supply Cables

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To install PSU cables, shut the PC down, unplug it, and mount the power supply in the case first. Connect the motherboard cable, the CPU power cable, and the PCIe cables to the graphics card, then connect each cable to the matching port on the PSU. Use only the cables that came with your PSU, and check each connector clicks into place before you power on.

  1. Shut down and unplug the PC

    Shut the PC down through the operating system, switch the PSU off, and unplug the power cord from the wall. Wait for the fans to stop and the lights to go out before you open the case. Follow the maker's manual for your case and power supply, and do not open the power supply itself. If the PSU shows damage or smells burnt, stop and contact the maker.

  2. Mount the power supply first

    Fit the PSU into the case mount with the fan facing the vent or the case floor, as the case manual shows. Fasten it with the screws from the case, and leave the modular cable ports facing inside the case where you can reach them. A fully modular PSU lets you connect only the cables your build needs, so the case stays clear for airflow.

  3. Connect the motherboard and CPU cables

    Find the wide motherboard cable and the CPU power cable in the PSU box. Push the motherboard cable into the matching socket on the board until it clicks, and do the same for the CPU cable near the top of the board. Route both cables behind the motherboard tray where the case allows it, so they stay clear of the fans.

  4. Connect the graphics card power

    Modern graphics cards take a 12V-2x6 connector, and the Corsair RM1000e, Corsair RM1000x, MSI MAG A850GL and Thermaltake Toughpower GT 850W each include a native 12V-2x6 cable. Push the connector straight into the card until it clicks, and check that it sits fully in the socket with no gap. Use only the cables that came with your PSU, since cables from other power supplies may not match.

  5. Check the cables before powering on

    Before you switch on, look at each connector and press any that feel loose. Check that no cable touches a fan blade and that the 12V-2x6 connector sits fully in the graphics card. Plug the power cord back in, switch the PSU on, and start the PC. If the PC does not start, switch it off, unplug it, and check the connections again.

What you need

CORSAIR RM1000e ATX 3.1 PCIe 5.1 Ready 1000W Power Supply

CORSAIR RM1000e ATX 3.1 PCIe 5.1 Ready 1000W Power Supply

A 1000W fully modular PSU with a native 12V-2x6 cable, a 120mm rifle bearing fan and a 7-year manufacturer warranty.

View on Amazon
CORSAIR RM1000x ATX 3.1 PCIe 5.1 1000W Power Supply

CORSAIR RM1000x ATX 3.1 PCIe 5.1 1000W Power Supply

A 1000W fully modular PSU with a native 12V-2x6 connector, Cybenetics Gold efficiency and a 10-year manufacturer warranty.

View on Amazon
MSI MAG A850GL PCIE5

MSI MAG A850GL PCIE5

An 850W fully modular PSU with 80 PLUS GOLD certification, a native dual-color 12V-2x6 cable and a 10-year limited warranty.

View on Amazon
Thermaltake Toughpower GT 850W ATX 3.1 Standard Power Supply

Thermaltake Toughpower GT 850W ATX 3.1 Standard Power Supply

An 850W fully modular PSU with 80 PLUS Gold efficiency, Smart Zero Fan and a native 12V-2x6 connector for modern GPUs.

View on Amazon

These come from our ranked list Best Power Supply, which compares them spec by spec.

FAQ

Can I use cables from another power supply?

No. Use only the cables that came with your PSU. Cables from other power supplies may not match the pin layout, and a wrong cable can damage parts.

How do I know the graphics card cable is seated?

Push the 12V-2x6 connector straight into the card until it clicks, then look at it from the side. The connector should sit fully in the socket with no gap showing.

Does a fully modular PSU need all its cables?

No. A fully modular PSU lets you connect only the cables your build needs. Leave the rest in the box, and the case stays clear for airflow.

What if the PC does not start after connecting the cables?

Switch the PC off, unplug it, and check each connector again. Push any loose connector in until it clicks, and check that the PSU switch is on before you try again.

Ranked power supplies guides