How to Mount a Monitor on an Arm
To mount a monitor on an arm, fix the arm to your desk, attach its mounting plate to the back of the monitor, then lift the monitor onto the arm and adjust height and tilt. Check the arm's rated load against your monitor's weight before you start, and follow the steps in the arm's manual for its own mounting method.
Check the arm fits your monitor and desk
Look at the back of the monitor for the mounting holes and compare their layout with the plate on the arm. Check your monitor's weight against the load the arm is rated for, and check whether the arm clamps to the desk edge or needs a grommet hole. Make sure the desk edge is solid and clear of drawers or supports where the clamp will sit.
Take the stand off the monitor
Unplug the power and video cables, then lay the monitor face down on a soft cloth or towel so the screen is protected. Undo the screws or release catch that holds the stand and lift it away. Keep the stand and its screws in case you need them later, and leave the mounting holes clear.
Fix the arm to the desk
Set the clamp over the desk edge or feed the bolt through the grommet hole, following the steps in the arm's manual. Tighten the clamp by hand until the arm sits firm and does not rock when you push it. Leave the arm folded back while you work so it stays out of the way.
Attach the plate to the monitor
Line up the arm's plate with the mounting holes on the back of the monitor. Use the screws that came with the arm, since screws that are too long can press into the monitor and screws that are too short will not hold. Tighten each screw until it is snug, and do not force it past that point.
Hang the monitor and set the position
Lift the monitor with both hands and slide or hook its plate onto the arm, then tighten the screw or catch that locks it in place. Adjust the height, tilt and swivel until the screen faces you squarely from your chair, and tighten the joints so the monitor holds its position. Route the cables through the clips on the arm and plug them back in.
What you need

Dell 24 Monitor SE2426H
A 23.8-inch 1920x1080 IPS monitor with a 144 Hz refresh rate, tilt and two HDMI ports, weighing 7.43 lb.
View on Amazon
Dell 27 Gaming Monitor SE2726HG
A 27-inch 1920x1080 IPS monitor with a 240 Hz refresh rate, DisplayPort 1.4 and two HDMI ports, weighing 8.2 lb.
View on Amazon
Acer 23.8-inch Office Monitor KB242Y G0bi
A 23.8-inch 1920x1080 IPS monitor with a 120 Hz refresh rate, HDMI and VGA ports and VESA mounting, weighing 7.72 lb.
View on Amazon
Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T
A 24-inch 1920x1080 monitor with a 100 Hz refresh rate, DisplayPort and two HDMI ports, built-in speakers and VESA mounting, at 5.8 lb.
View on AmazonThese come from our ranked list Best PC with Monitor, which compares them spec by spec.
FAQ
Can any monitor go on a monitor arm?
Most monitors with mounting holes on the back can. Check that the hole layout matches the arm's plate and that the monitor's weight sits within the load the arm is rated for.
Do I need tools to mount a monitor on an arm?
Check the arm's manual for the tools it needs. You may also want a screwdriver for the stand screws and a soft cloth to protect the screen while the monitor lies face down.
What should I check before buying a monitor arm?
Check the back of the monitor and its manual for the mounting hole pattern before you buy an arm. The Acer and Sceptre monitors below list VESA mounting, so an arm plate made for that pattern fits them.
How do I stop the monitor from drooping?
Tighten the tilt joint and adjust the tension screw on the arm until the monitor holds its position. If it still drops, the monitor may weigh more than the load the arm is rated for.



