How to Mount Dual Monitors on a Stand
To mount two monitors on one stand, attach each monitor to the stand's arms with the VESA screws, clamp or bolt the stand to the desk, then connect each monitor to the computer and set the two screens side by side in the display settings. Check the stand's VESA pattern and weight rating against each monitor first, so the arms hold both screens level and steady.
Check the VESA pattern and weight
Look at the back of each monitor for the VESA pattern and the screw size the stand needs. The Acer KB242Y G0bi is VESA mountable, and the Sceptre E248W-FW100T has a VESA wall mount pattern. Match the pattern on the stand's plates to the holes on each monitor, and check the stand's weight rating against the monitor weights: the Sceptre weighs 5.8 lb, the Dell SE2426H weighs 7.43 lb, the Acer weighs 7.72 lb, and the Dell SE2726HG weighs 8.2 lb. If the pattern does not line up, the monitor will not sit square on the arm.
Attach the arms to the desk
Set the stand on the desk where the monitors will sit, with room for the arms to swing and for the cables to reach the computer. Clamp the stand to the edge of the desk or bolt it through a grommet hole, then tighten the clamp until the base does not wobble. Put the monitors face down on a soft surface before you lift them onto the arms, so the screens do not press against the desk.
Fix each monitor to an arm
Lift one monitor at a time onto its arm and line up the plate with the VESA holes on the back. Drive the screws in by hand first, then tighten them with a screwdriver until the monitor sits firm on the plate. Do not overtighten, since the screws only need to hold the monitor still. Repeat the same steps for the second monitor, then check that both screens sit at the same height before you move on.
Connect the cables and set the layout
Connect each monitor to the computer with its own cable. The Dell SE2426H and the Dell SE2726HG each have two HDMI ports, and the Dell SE2726HG and the Sceptre E248W-FW100T also have a DisplayPort. The Acer KB242Y G0bi has HDMI and VGA. Then open the display settings on the computer and arrange the two screens side by side, with the main screen on the side you use most. Route the cables along the stand's arms so they do not pull on the ports.
What you need

Dell 24 Monitor SE2426H
A 23.8-inch 1920x1080 IPS monitor with a 144 Hz refresh rate, two HDMI ports, and a 7.43 lb weight for a dual-monitor stand.
View on Amazon
Dell 27 Gaming Monitor SE2726HG
A 27-inch 1920x1080 IPS monitor with a 240 Hz refresh rate, two HDMI ports, DisplayPort 1.4, and an 8.2 lb weight.
View on Amazon
Acer 23.8-inch Office Monitor KB242Y G0bi
A 23.8-inch 1920x1080 IPS monitor with a 120 Hz refresh rate, HDMI and VGA, and VESA mounting for a dual-monitor stand.
View on Amazon
Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T
A 24-inch 1920x1080 monitor with a 100 Hz refresh rate, DisplayPort and two HDMI ports, built-in speakers, and a VESA wall mount pattern.
View on AmazonThese come from our ranked list Best PC with Monitor, which compares them spec by spec.
FAQ
Do both monitors need the same size?
No. The Dell SE2726HG is 27 inches while the Dell SE2426H and the Acer KB242Y G0bi are 23.8 inches and the Sceptre E248W-FW100T is 24 inches. Mixed sizes work on a dual stand, but matching heights keeps the tops of the screens level.
Can I mount monitors with different ports?
Yes. Connect each monitor with its own cable to the computer. All four monitors have HDMI, and the Acer KB242Y G0bi also has VGA. The Dell SE2726HG and the Sceptre E248W-FW100T also have DisplayPort.
What if the monitors sit at different heights?
Loosen the arm, slide the lower monitor up until its top lines up with the other screen, then tighten the arm again. Check the height from the front of the desk so both screens sit level before you connect the cables.



