Amazon Black Friday Week deals

Paid link

Monitors · How-to guide

How to Connect a Monitor to a PC Tower

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

Connect the monitor to your PC tower with an HDMI or DisplayPort cable, plug both into power, and turn the monitor on. The tower sends its picture through that one cable, so matching the cable to a port on both ends is the whole job. If the screen stays blank, check that the cable is fully seated and that the monitor is set to the right input.

  1. Check the ports on your tower

    Look at the back of the tower for HDMI and DisplayPort outputs. If the tower has a graphics card, use the ports on the card, low on the back of the case, rather than the ports on the motherboard. The Dell 27 monitor has DisplayPort 1.4 and HDMI. The Acer has HDMI and VGA. The Sceptre has DisplayPort and two HDMI ports. One of those cables should match a port on your tower.

  2. Pick the right cable

    Use an HDMI or DisplayPort cable that matches a port on both the tower and the monitor. Both carry picture and sound, so either works for everyday use. A cable that fits loosely can drop the signal, so push each end in until it sits firmly. If the tower and the monitor share no port type, you need an adapter or a different cable.

  3. Plug in the monitor and the power

    Connect the cable from the tower to the monitor, then plug the monitor and the tower into power. Turn the monitor on first, then the tower. Use the buttons on the monitor to open its menu and pick the input that matches the cable you used, such as HDMI or DisplayPort. The picture should appear once the PC finishes starting.

  4. Set the resolution and refresh rate

    Open the display settings on your PC and check that the monitor is set to 1920x1080, the resolution all four monitors here use. Then set the refresh rate to what your monitor supports: 144Hz on the Dell 24, 240Hz on the Dell 27, 120Hz on the Acer, and 100Hz on the Sceptre. Choose to extend the desktop if you use a second screen, or duplicate it to mirror the same picture.

  5. Fix a blank screen

    If the screen stays blank, first check that the cable is fully seated at both ends and that the monitor is set to the right input. Try a different port on the tower, and try the ports on the graphics card if the tower has one. A faulty cable is a common cause, so swap in a spare cable before assuming the monitor or the tower is at fault.

What you need

Dell 24 Monitor SE2426H

Dell 24 Monitor SE2426H

A 23.8-inch 1080p IPS monitor with a 144Hz refresh rate, 1ms response, FreeSync and two HDMI ports.

View on Amazon
Dell 27 Gaming Monitor SE2726HG

Dell 27 Gaming Monitor SE2726HG

A 27-inch 1080p IPS monitor with a 240Hz refresh rate, FreeSync Premium, HDMI and DisplayPort 1.4.

View on Amazon
Acer 23.8-inch Office Monitor KB242Y G0bi

Acer 23.8-inch Office Monitor KB242Y G0bi

A 23.8-inch 1080p IPS office monitor with a 120Hz refresh rate, Adaptive-Sync, HDMI and VGA.

View on Amazon
Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T

Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T

A 24-inch 1080p monitor with a 100Hz refresh rate, FreeSync, built-in speakers, DisplayPort and two HDMI ports.

View on Amazon

These come from our ranked list Best PC with Monitor, which compares them spec by spec.

FAQ

Do I need a graphics card to connect a monitor to a PC tower?

No. Most towers have video outputs on the motherboard, but if your tower has a graphics card, use its HDMI or DisplayPort outputs instead, since the motherboard ports may stay off when a card is fitted.

Which is better for a monitor, HDMI or DisplayPort?

Both carry picture and sound, and either works for everyday use. Pick the cable that matches a port on both your tower and your monitor, and check that it is fully seated at both ends.

Why does my monitor say no signal after I plug it in?

The cable may not be fully seated, the monitor may be set to the wrong input, or the cable may be plugged into a motherboard port while a graphics card is fitted. Reseat the cable, pick the right input, and try the ports on the graphics card.

Ranked monitors guides