Amazon Black Friday Week deals

Paid link

Monitors · How-to guide

How to Clean a Monitor Stand

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To clean a monitor stand, unplug the monitor and lift it off the desk so you can reach the whole stand. Wipe the dust off with a dry, soft cloth, then wipe again with a cloth lightly damp with water and dry it right away. Clean the joints and the base last, and let the stand dry before you put the monitor back.

  1. Unplug the monitor and clear the desk

    Unplug the monitor from power and move papers, cables and cups away from the stand. Lift the monitor and stand away from the wall so you can reach the back and the underside of the base. If the stand comes off the monitor, remove it the way the manual shows and set the screen face down on a soft, flat surface.

  2. Dust the stand first

    Start with a dry, soft cloth and wipe the stand from top to bottom so dust falls to the desk, not onto the parts you already cleaned. Wipe the neck, the tilt joint and the base, and use a soft brush for dust caught in the joints and around the screws. Shake the cloth out often so you are not moving the same dust around the stand.

  3. Wipe it with a damp cloth

    Dampen a clean, soft cloth with water and wring it out so it is barely wet. Wipe the base and the neck in long strokes, and turn the cloth to a clean side when it picks up dirt. For a sticky mark, add a small drop of mild soap to the cloth and wipe the spot, then wipe it again with a cloth damp with plain water. Never spray liquid straight onto the stand or the monitor.

  4. Clean the joints and the base

    Move the tilt joint slowly through its range while you wipe, so you reach the folds where dust gathers. Wipe the underside of the base and the feet, where dust and crumbs collect out of sight. Wipe around the screws without forcing them, and leave any screw that feels loose for the maker to check.

  5. Dry it and put the monitor back

    Dry the stand with a clean, dry cloth, then leave it for a few minutes so any dampness in the joints dries out. Put the monitor back on the desk and set it at the angle you want. Plug the power and video cables back in, then check that the monitor sits level and steady on the stand.

What you need

Dell 24 Monitor SE2426H

Dell 24 Monitor SE2426H

A 23.8-inch 1920x1080 IPS display with a 144Hz refresh rate, a 178° viewing angle and a tilt stand.

View on Amazon
Dell 27 Gaming Monitor SE2726HG

Dell 27 Gaming Monitor SE2726HG

A 27-inch 1920x1080 IPS display with a 240Hz refresh rate, 99% sRGB color coverage and a tilt stand.

View on Amazon
Acer 23.8-inch Office Monitor KB242Y G0bi

Acer 23.8-inch Office Monitor KB242Y G0bi

A 23.8-inch 1920x1080 IPS display with a 120Hz refresh rate, 99% sRGB coverage and VESA mounting.

View on Amazon
Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T

Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T

A 24-inch 1920x1080 display with a 100Hz refresh rate, 100% sRGB color gamut and a VESA wall mount pattern.

View on Amazon

These come from our ranked list Best PC with Monitor, which compares them spec by spec.

FAQ

Can I use glass cleaner on a monitor stand?

No. Glass cleaner and household sprays can leave marks on plastic and metal and drip into the joints. Use a cloth damp with water, and add a small drop of mild soap only for a sticky mark.

How do I clean dust from the stand joints?

Use a dry, soft brush or a dry cloth to push the dust out of the joints, then wipe with a damp cloth. Move the tilt joint slowly through its range while you wipe so you reach the folds where dust gathers.

Should I take the stand off the monitor to clean it?

Take it off only if the manual shows how. Many stands unclip or unscrew from the monitor, which makes the base and neck easier to reach. If the manual does not show removal, clean the stand while it stays attached.

Ranked monitors guides