Amazon Black Friday Week deals

Paid link

PC Components · How-to guide

How to Install a Motherboard in a PC

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To install a motherboard, check that its socket, memory generation and form factor match your processor, memory and case, then mount the board on the case standoffs and connect the power, front-panel and storage cables. The steps below follow that order from preparation to the first start.

  1. Shut down, unplug and check the match

    Shut the PC down and unplug it before you open the case, and follow the maker's manual for your case and board. Then confirm the match on paper: an AM4 board takes AM4 processors, an AM5 board takes AM5 processors and an LGA 1700 board takes LGA 1700 processors. Check the memory generation too, since DDR4 and DDR5 slots take different memory, and confirm the case accepts the board's form factor, such as ATX or Micro-ATX.

  2. Fit the standoffs and the rear shield

    Lay the case on its side and compare the standoff positions in the case with the mounting holes on the board. Move or add standoffs so one sits under each hole and every standoff sits under a hole. Fit the rear I/O shield into the case opening if your board uses a separate shield, with the port labels facing out. Some boards have the shield attached, so check the manual before you push anything into place.

  3. Seat the board and drive the screws

    Lower the board onto the standoffs at a slight angle so the rear ports slide into the shield openings. Check that every mounting hole lines up with a standoff and that no cable is trapped under the board. Drive a screw into each hole and snug them down in turn, working across the board rather than tightening one corner fully first. The board should sit flat and not flex when you press near a corner.

  4. Connect power, front panel and storage

    Connect the main power cable from the power supply to the board's main power connector, then connect the CPU power cable to the connector near the processor socket. Attach the front-panel wires for the power switch, reset switch and indicator lights, matching the pin layout printed in the manual. Connect your storage drives and case fans, then route the cables so they stay clear of fan blades and the board's heatsinks.

  5. Start the PC and check the setup screen

    Plug the PC in and start it. If the setup screen opens, check that the processor, memory and storage drives appear as expected, then save and exit. If nothing appears, shut down, unplug, and recheck the power cables, memory seating and front-panel wires against the manual. Do not open a power supply or a device under warranty; contact the maker instead.

What you need

ASUS ROG Strix B550-F Gaming

ASUS ROG Strix B550-F Gaming

An AM4 ATX board for Ryzen 3000 and 5000 series processors, with DDR4, PCIe 4.0, dual M.2 slots, WiFi 6E and HDMI 2.1 output.

View on Amazon
GIGABYTE B850 AORUS Elite WIFI7

GIGABYTE B850 AORUS Elite WIFI7

An AM5 ATX board for Ryzen 9000, 8000 and 7000 series processors, with DDR5, PCIe 5.0, three M.2 slots, Wi-Fi 7 and a 5-year warranty.

View on Amazon
GIGABYTE B550M K

GIGABYTE B550M K

An AM4 Micro-ATX board for Ryzen 5000, 4000 and 3000 series processors, with DDR4, a PCIe 4.0 x16 slot and two M.2 slots.

View on Amazon
MSI PRO B760-P

MSI PRO B760-P

An LGA 1700 ATX board for 12th and 13th Gen Intel Core processors, with DDR4, PCIe 4.0, Wi-Fi 6E and 2.5Gbps LAN.

View on Amazon

These come from our ranked list Best Motherboard, which compares them spec by spec.

FAQ

Do I fit the processor and memory before mounting the board?

Either order works. Fitting the processor, cooler and memory while the board is on the bench gives you more room, and mounting the board first keeps the case work in one place. Follow the cooler and board manuals for the mounting hardware either way.

What if the board holes do not line up with the standoffs?

Stop and check the form factor. An ATX board and a Micro-ATX board use different hole patterns, so move the standoffs to the positions marked for your board size in the case manual. Drive screws only through holes that line up with a standoff.

What should I check if the PC does not start after installation?

Shut down and unplug the PC, then recheck the main and CPU power cables, the memory seating and the front-panel power switch wire against the manual. If the parts still do not appear in the setup screen, check the maker's support pages for your exact board and processor.

Ranked motherboards guides