Amazon Black Friday Week deals

Paid link

PC Components · How-to guide

How to Attach a Motherboard to a Case

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To attach a motherboard to a case, fit the standoffs for your board size, set the board on them so the rear ports line up, and fasten it with the board screws. Shut the PC down and unplug it first, and follow the manuals for your case and motherboard. The case must list your board size, so check the form factor before you start.

  1. Check the board fits the case

    Cases list the board sizes they take, such as ATX or Micro-ATX, and the board must match one of those sizes. Read the form factor in your motherboard manual and compare it with the form factor the case lists. A board that is larger than the case supports will not line up with the standoffs or the rear slots, so confirm the match before you fit anything.

  2. Fit the standoffs for your board

    Shut the PC down, unplug it, and follow the manuals for your case and motherboard. Fit a standoff in each case hole that matches your board size, and leave out any hole with no matching board hole, since an extra standoff under the board can short it. Set the rear I/O shield in the case opening first if your board uses a separate one.

  3. Set the board on the standoffs

    Hold the board by its edges and lower it onto the standoffs so the rear ports sit in the shield and the mounting holes line up with the standoffs below. Do not force the board down or slide it across the standoffs, since the solder points on the underside can catch. Check that every mounting hole has a standoff under it before you fasten anything.

  4. Fasten the board and check it

    Fasten the board screws in a crisscross order, turning each one a little at a time so the board settles flat instead of pulling to one side. Tighten them until they are snug, and stop there, since overtightening can crack the board or strip the standoff. Give the board a gentle push to confirm it sits firm, then connect the case and power cables.

What you need

ASUS ROG Strix B550-F Gaming

ASUS ROG Strix B550-F Gaming

An ATX board with an AM4 socket, B550 chipset, DDR4 memory, WiFi 6E, PCIe 4.0 and dual M.2 slots.

View on Amazon
GIGABYTE B850 AORUS Elite WIFI7

GIGABYTE B850 AORUS Elite WIFI7

An ATX board with an AM5 socket, B850 chipset, DDR5 memory, WiFi 7, PCIe 5.0 and 3 M.2 slots.

View on Amazon
GIGABYTE B550M K

GIGABYTE B550M K

A Micro-ATX board with an AM4 socket, B550 chipset, DDR4 memory, 4 DIMM slots and 2 M.2 slots.

View on Amazon
MSI PRO B760-P

MSI PRO B760-P

An ATX board with an LGA 1700 socket, B760 chipset, DDR4 memory, WiFi 6E and Bluetooth 5.3.

View on Amazon

These come from our ranked list Best Motherboard, which compares them spec by spec.

FAQ

Do I need standoffs for every board hole?

Yes. Each mounting hole on the board needs a standoff under it, and any standoff with no board hole above it should come out. A standoff in the wrong place can touch a solder point on the underside of the board.

What if the rear ports do not line up?

Lift the board off and check the standoff positions and the rear shield before you try again. A standoff in the wrong hole or a shield that sits crooked will push the board out of line, so fix the position first.

How tight should the board screws be?

Snug is enough. Tighten each screw until it stops turning freely, then stop, since overtightening can crack the board or strip the standoff. If a screw keeps turning without biting, the standoff below it may be loose.

Ranked motherboards guides