How to Attach a Monitor to a Stand
To attach a monitor to a stand, check that the stand fits your monitor's mount pattern, lay the monitor face down on a soft surface, line up the stand's bracket with the holes on the back, and fasten it with the screws the stand provides. Set the monitor upright and check that it sits level. Check the monitor's manual for the mount pattern and screw size before you start.
Check the mount pattern and weight
Look at the back of your monitor for the screw holes and check the manual for the mount pattern and the screws it takes. Check the stand's notes for the patterns it fits and the weight it holds, and check your monitor's weight in its manual. Buy the stand whose notes name your monitor's pattern and the weight it holds. A monitor with screw holes on the back takes a stand; a monitor with a plain back uses the base the maker supplies.
Lay the monitor face down
Unplug the monitor and set it face down on a soft, flat surface such as a towel on a table, so the screen does not press against anything hard. Keep the screen clear of tools and screws while you work. If the monitor has a base or foot attached, remove it as the manual shows before you fit the stand bracket. Leave the cables unplugged until the monitor is on the stand and upright.
Fit the bracket to the back
Hold the stand's bracket against the back of the monitor and line up its holes with the holes on the monitor. Put in the screws the stand provides and turn each one a little at a time so the bracket sits flat. Do not use screws from another mount, and do not force a screw that does not turn. Check that each screw is snug and that the bracket does not move when you press it gently.
Mount the monitor on the stand
Lift the monitor by its sides and set it onto the stand base or arm as the stand's manual shows. Tighten the knob or screw that locks the monitor to the stand, then let go slowly and check that it holds. Adjust the tilt and height as the stand allows, and check that the monitor stays where you set it. If it slips or leans, take it off and check the bracket and the lock again.
Connect the cables and check the picture
Plug the video cable into the monitor and the computer, using HDMI or DisplayPort as your computer and monitor allow. Check that your computer's port supports video output before you rely on a USB-C cable for the picture. Plug in the power cable, switch the monitor on, and check that the picture fills the screen. If the screen stays blank, check the cable and the input the monitor is set to.
What you need

Dell 24 Monitor SE2426H
A 23.8-inch 1920x1080 IPS display with a 144 Hz refresh rate and HDMI, with tilt adjustment.
View on Amazon
Dell 27 Gaming Monitor SE2726HG
A 27-inch 1920x1080 IPS display with a 240 Hz refresh rate, HDMI, DisplayPort 1.4, and tilt adjustment.
View on Amazon
Acer 23.8-inch Office Monitor KB242Y G0bi
A 23.8-inch 1920x1080 IPS display with a 120 Hz refresh rate, HDMI, VGA, and VESA mountable.
View on Amazon
Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T
A 24-inch 1920x1080 display with a 100 Hz refresh rate, DisplayPort, two HDMI ports, built-in speakers, and a VESA wall mount pattern.
View on AmazonThese come from our ranked list Best PC with Monitor, which compares them spec by spec.
FAQ
Do all monitors fit a stand?
No. A monitor fits a stand when the stand lists the monitor's mount pattern and weight. Check the monitor's manual for the pattern and the screws it takes, and check the stand's notes before you buy it.
Can I use screws from another mount?
Use only the screws the stand provides or the size the monitor's manual names. A screw that is too long can reach parts inside the monitor, and one that is too short will not hold the bracket.
What if the back of my monitor is plain?
Some monitors use only the base the maker supplies. Check the back of the monitor and its manual before you buy a stand, and use the maker's base for a monitor with a plain back.



