How to Assemble a Motherboard
To assemble a motherboard, fit the CPU, memory and M.2 drives first, then mount the board on the case standoffs, connect the power and front-panel cables, then install the cooler and the graphics card. Work on a flat surface, shut the PC down and unplug it before you open the case, and follow the manual that came with your board.
Check the board, case and parts first
Start by checking that the board fits the case: an ATX board needs an ATX case, and a Micro-ATX board fits a Micro-ATX or ATX case. Check that the CPU matches the socket on the board, and that the memory matches the board's memory generation, DDR4 or DDR5. Lay out the board, CPU, memory, cooler, storage and power cables on a flat surface, and read the board manual for the socket, slot and connector layout before you fit anything.
Fit the CPU, memory and M.2 drives
Lift the socket lever, line up the CPU with the socket marker and lower it in without force, then close the lever. Push the memory sticks into the slots the manual shows, pressing both ends until the clips close. Slide each M.2 drive into its slot at a slight angle, press it flat and fix it with the screw or latch the board provides. Keep the board on its box or a flat surface while you work, and touch a metal part of the case often to discharge static.
Mount the board in the case
Fit the I/O shield into the back of the case, then set the board onto the standoffs already fixed in the case and line up the screw holes. Screw the board down in a cross pattern, snug but not overtightened, so the board sits flat and cannot flex. Check that no standoff sits under the board where there is no hole, since a stray standoff can short the board. Connect the case fans and the front-panel cables to the headers the manual shows.
Connect power and the front-panel cables
Plug the main power cable from the power supply into the board, then plug the CPU power cable into the socket near the top of the board. Connect the front-panel cables for the power button, reset button and lights to the header the manual shows, fitting each cable onto the header pins for power, reset and lights. Plug the CPU cooler fan into the CPU fan header so the board can control it. Route the cables away from the fans and the board so nothing catches when the fans spin.
Install the cooler and graphics card
Fit the cooler over the CPU following the cooler manual, and plug its fan into the CPU fan header. Push the graphics card into the top PCIe slot until the latch clicks, then fix it to the case with screws and plug in its power cables if it has them. Check that the card sits level and that its fans have room to spin. Close the case, plug the PC in, switch it on and open the BIOS to check that the CPU, memory and drives show up.
What you need

ASUS ROG Strix B550-F Gaming
A DDR4 ATX board with an AM4 socket, PCIe 4.0, dual M.2 slots and WiFi 6E for a Ryzen 3000 or 5000 series build.
View on Amazon
GIGABYTE B850 AORUS Elite WIFI7
A DDR5 ATX board with an AM5 socket, PCIe 5.0, three M.2 slots and WiFi 7 for a Ryzen 7000, 8000 or 9000 series build.
View on Amazon
GIGABYTE B550M K
A DDR4 Micro-ATX board with an AM4 socket, PCIe 4.0 and two M.2 slots for a Ryzen 3000, 4000 or 5000 series build.
View on Amazon
MSI PRO B760-P
A DDR4 ATX board with an LGA 1700 socket, PCIe 4.0 and WiFi 6E for a 12th, 13th or 14th Gen Intel build.
View on AmazonThese come from our ranked list Best Motherboard, which compares them spec by spec.
FAQ
Do I need to install the CPU before mounting the board?
Yes. Fit the CPU, memory and M.2 drives while the board is out of the case, since the board is easier to reach on a flat surface. Mount the board only after those parts are in place.
What holds the motherboard in the case?
Metal standoffs fixed in the case hold the board off the case floor, and screws through the board holes fix it to the standoffs. Check that a standoff sits under each hole and that no extra standoff touches the board.
How do I know the board works after assembly?
Plug the PC in, switch it on and open the BIOS to check that the CPU, memory and drives show up. If the PC does not start, check the power cables and the front-panel cables first, then read the board manual.



