Amazon Black Friday Week deals

Paid link

Monitors · How-to guide

How to Adjust a Dual Monitor Stand Height

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To adjust a dual monitor stand, find the height lock on each arm, lift or lower the monitors to the same height, then lock each arm and check the screens line up. Check the manual for the lock on your stand before you move anything. Set the height with the monitors on, since the weight of the screens changes how the arms sit.

  1. Find the height lock on each arm

    Look at the stand for the height lock on each arm: a knob, a lever or a screw on the pole or the arm itself. Check the manual for your stand to find the lock and how it works, and read it before you loosen anything. Hold the monitor with one hand while you loosen the lock with the other, since the arm can drop once the lock is loose. The Sceptre monitor weighs 5.8 lb and the Dell 27 monitor weighs 8.2 lb, so check the stand holds the weight of the monitors you mount.

  2. Set both monitors to the same height

    Raise or lower one monitor at a time until the tops of the two screens sit level. Match the height at the bezels, not at the stands, since the arms may sit at different points on the pole. Lock each arm as you set it, then step back and look at the two screens together. If one screen sits higher, loosen its lock, move it a little, and lock it again.

  3. Level the screens and set the tilt

    With the height set, level each screen so the picture runs straight across both monitors. The Dell 24 and Dell 27 monitors tilt, so tilt each screen by the same amount and check the picture from your chair. If the screens lean, loosen the tilt lock, straighten the screen, and tighten the lock again. A level pair keeps the seam between the screens straight.

  4. Check the cables after you move them

    Moving the screens can pull the cables tight, so check each cable has slack after you set the height. Every monitor here has HDMI, and the Dell 27 and the Sceptre also have DisplayPort, so match the cable to the port on each monitor. Push each plug in fully and check the picture shows on both screens. If a screen stays dark, check the plug and the input on that monitor.

  5. Lock the arms and check they hold

    Tighten every lock once the height, level and tilt look right. Let go of the monitors and watch the arms for a moment to check they hold their height. If an arm sinks, tighten its lock as the manual directs and check the stand holds the weight of the monitor on it. Do not force a lock past its stop.

What you need

Dell 24 Monitor SE2426H

Dell 24 Monitor SE2426H

A 23.8-inch 1920x1080 IPS monitor with a 144 Hz refresh rate, 1ms response, 2X HDMI and tilt, at 7.43 lb.

View on Amazon
Dell 27 Gaming Monitor SE2726HG

Dell 27 Gaming Monitor SE2726HG

A 27-inch 1920x1080 IPS monitor with a 240 Hz refresh rate, 0.5ms response, DisplayPort 1.4, 2X HDMI and tilt, at 8.2 lb.

View on Amazon
Acer 23.8-inch Office Monitor KB242Y G0bi

Acer 23.8-inch Office Monitor KB242Y G0bi

A 23.8-inch 1920x1080 IPS monitor with a 120 Hz refresh rate, 1ms response, HDMI, VGA and a VESA mount, at 7.72 lb.

View on Amazon
Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T

Sceptre 24-inch Gaming Monitor 1ms E248W-FW100T

A 24-inch 1920x1080 monitor with a 100 Hz refresh rate, 1ms response, DisplayPort, 2X HDMI, built-in speakers and a VESA mount, at 5.8 lb.

View on Amazon

These come from our ranked list Best PC with Monitor, which compares them spec by spec.

FAQ

Do both monitors need the same height?

Yes, for a dual setup. Set each arm to the same height so the screens line up and the picture runs straight across both monitors.

What if one monitor will not stay up?

Check the height lock on that arm and tighten it as the manual directs. If the arm still drops, check the stand holds the weight of the monitor on it.

Can I mount these monitors on a stand?

The Acer and Sceptre monitors have a VESA mount. The Dell monitors tilt, so check the manual or spec sheet for the mount pattern on those two before you buy a stand.

Which cable do I use for each monitor?

Every monitor here has HDMI, and the Dell 27 and the Sceptre also have DisplayPort. Match the cable to the port on the monitor and on your computer, and check the cable reaches after you move the screens.

Ranked monitors guides