Amazon Black Friday Week deals

Paid link

Keyboards & Mice · How-to guide

Mechanical Keyboard Stabilizer Types

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

A stabilizer is the wire and housing under a long key, such as the spacebar, Enter or Shift, that keeps the key level when you press one side. The main types are plate-mount, which clips into the metal plate, and PCB-mount, which screws or clips into the circuit board.

  1. What a stabilizer does

    Long keys such as the spacebar, Enter, Shift and Backspace are too wide for one switch to hold level, so a stabilizer runs a wire between two housings under the key. When you press one end, the wire pulls the other end down with it, so the key travels straight. Without a stabilizer, a long key would tilt, bind or rattle on one side. Every mechanical keyboard with long keys uses one of the types below.

  2. Plate-mount stabilizers

    A plate-mount stabilizer clips into the metal plate that sits above the circuit board, with the wire running under the plate. To remove one, pull the keycap and the switch above it, then unclip the housings from the plate. Plate-mount types fit boards built with a plate, and they come out without touching the circuit board. Their wire can rattle against the housings if it runs dry.

  3. PCB-mount stabilizers

    A PCB-mount stabilizer fastens straight to the circuit board, either with screws or with clips that snap into holes in the board. Screw-in types hold the housings firm, so the wire moves less and the key feels steadier. Clip-in types snap in and out by hand, so they swap faster than screw-in types. To reach either type, pull the keycap and the switch above it first.

  4. How to tell which type you have

    Pull the keycap off a long key and look at the housings on each side of the switch. If the housings sit in the metal plate, you have plate-mount stabilizers. If they sit on the circuit board with screws, you have screw-in PCB-mount stabilizers, and if they snap into the board with no screws, you have clip-in stabilizers. Check the board's notes before you buy a replacement set.

  5. Lubing and tuning stabilizers

    A thin coat of lube on the wire ends and inside the housings quiets the rattle that dry stabilizers make. Work a small amount into each housing and along the wire, then press the key a few times and listen for ticking or rattle. The two AULA F75 Pro keyboards here ship with pre-lubricated stabilizers, so they show how a lubed stabilizer sounds. Add lube only where the wire meets the housing.

What you need

AULA F75 Pro Wireless Mechanical Keyboard

AULA F75 Pro Wireless Mechanical Keyboard

A 75% hot-swappable keyboard in black with pre-lubricated stabilizers and LEOBOG reaper switches.

View on Amazon
AULA F75 Pro Wireless Mechanical Keyboard

AULA F75 Pro Wireless Mechanical Keyboard

A 75% hot-swappable keyboard in gradient blue with pre-lubricated stabilizers and LEOBOG star vector switches.

View on Amazon
Redragon Mechanical Gaming Keyboard Wired

Redragon Mechanical Gaming Keyboard Wired

A wired hot-swappable keyboard with red switches and 4 spare switches, so you can pull switches to reach the stabilizers.

View on Amazon
Aula WIN60 HE

Aula WIN60 HE

A 60% wired keyboard with hot-swappable magnetic switches and adjustable actuation, for switch swaps while you work on stabilizers.

View on Amazon

These come from our ranked list Best Mechanical Keyboard, which compares them spec by spec.

FAQ

Do all mechanical keyboards use the same stabilizers?

No. Boards use plate-mount or PCB-mount stabilizers, and PCB-mount types split into screw-in and clip-in. Check which type your board has before you buy a replacement set.

Can I swap stabilizers on a hot-swappable keyboard?

Yes, if the switches lift out. Pull the keycap and the switch above the stabilizer, then unclip or unscrew the housings. The AULA F75 Pro boards support 3-pin or 5-pin switch swaps, so their switches lift out without soldering.

Why does my spacebar rattle?

A dry wire rattling against its housings is one cause. Add a thin coat of lube where the wire meets each housing, then press the key and listen. The AULA F75 Pro boards ship with pre-lubricated stabilizers and five layers of filling silencer.

Ranked keyboards guides