Amazon Black Friday Week deals

Paid link

Keyboards & Mice · How-to guide

How to Take Off Mechanical Keyboard Keys

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To take off a mechanical keyboard key, hook a keycap puller under the keycap and pull straight up. The keycap lifts off the switch stem underneath, and you can then clean around the switch or swap the cap. Unplug the keyboard first, and take a photo of the layout so every key goes back in the right place.

  1. Unplug the keyboard and photograph the layout

    Disconnect the keyboard from the computer before you touch any keys, and turn off wireless keyboards. Take a clear photo of the full layout from above so you can see where each keycap belongs. Keep the removed caps in rows on a tray or towel in the same order as the board, so nothing gets mixed up while you work.

  2. Hook the puller under the keycap

    Place the arms of a wire keycap puller under opposite sides of the keycap and squeeze gently so the hooks catch the underside. Pull straight up with slow, even pressure until the cap comes free from the switch stem. If a cap resists, wiggle the puller slightly from side to side instead of forcing it, since a hard yank can bend the stem or crack the cap.

  3. Lift larger keys with extra care

    Longer keys such as the spacebar, Shift and Enter sit on stabilizer bars that keep them level when pressed. Lift these caps straight up and keep the pull even across the whole key so the stabilizer stays in place. If a stabilizer bar pops loose, set the cap aside and refit the bar before you press the cap back down, following the layout in your photo.

  4. Clean around the exposed switches

    With the caps off, brush loose dust and crumbs away from the plate and around each switch with a soft brush. Wipe the plate with a dry cloth and leave any damp cleaning for the keycaps themselves, which you can wash separately and dry fully before refitting. Check that no debris sits between the switch stems before you start putting caps back.

  5. Press the keycaps back into place

    Line each keycap up over its switch stem using your photo as a guide, then press it down firmly until it sits flat and level with the keys around it. Work through the board row by row so no key ends up in the wrong spot. When every cap is back, plug the keyboard in and press each key to confirm it registers and feels right.

What you need

AULA F75 Pro Wireless Mechanical Keyboard

AULA F75 Pro Wireless Mechanical Keyboard

A 75% wireless keyboard with a hot-swappable base, LEOBOG reaper switches and side-printed PBT keycaps.

View on Amazon
AULA F75 Pro Wireless Mechanical Keyboard

AULA F75 Pro Wireless Mechanical Keyboard

A 75% wireless keyboard with a hot-swappable base, LEOBOG star vector switches and gradient blue side-printed PBT keycaps.

View on Amazon
Redragon Mechanical Gaming Keyboard Wired

Redragon Mechanical Gaming Keyboard Wired

A wired keyboard with a hot-swappable base, linear red switches, double-shot PBT keycaps and 11 backlit modes.

View on Amazon
Aula WIN60 HE

Aula WIN60 HE

A 60% wired keyboard with magnetic switches, a hot-swappable base and RGB backlighting.

View on Amazon

These come from our ranked list Best Mechanical Keyboard, which compares them spec by spec.

FAQ

Can I remove keycaps without a keycap puller?

You can, but a puller grips the cap evenly and lowers the chance of scratching the cap or bending the switch stem. Fingers or flat tools slip more easily and can mark the plastic. A wire keycap puller grips the cap from opposite sides.

Do I need to remove the switches as well?

No. The keycap lifts off the switch, and the switch stays in the board. On a hot-swappable board you can also pull switches out, but that is a separate step and only needed if a switch itself needs replacing.

Will removing keycaps void the warranty?

Check the warranty terms in the maker's manual before you start. If the manual says not to open the board, leave the work to the maker or an authorized service point instead.

How do I clean under the keys?

Brush dust and crumbs off the plate with a soft brush, then wipe it with a dry cloth. Wash the keycaps separately and dry them fully before pressing them back onto their switches.

Ranked keyboards guides