How to Replace Keyboard Switches
On a hot-swappable mechanical keyboard, you can replace a switch without soldering: pull off the keycap, pull the old switch out, and press the new one in until it seats. Before you start, check that your keyboard is hot-swappable and whether it takes 3-pin or 5-pin switches, since a membrane keyboard does not support swapping switches.
Check that your keyboard is hot-swappable
Not every keyboard lets you swap switches. A hot-swappable board has sockets that hold the switch pins, so you can pull a switch out and press a new one in with no soldering. The YUNZII B98 PRO, SOLAKAKA A99 Pro and KiiBoom Phantom98 Lite are all hot-swappable, while the AULA S99 is a membrane keyboard that does not support hot-swapping. If your board is soldered, replacing a switch means desoldering the old one, so check your keyboard's manual before you start.
Match the new switch to the board
Switches come with 3 pins or 5 pins, and the board must accept the type you buy. The YUNZII B98 PRO and SOLAKAKA A99 Pro both support 3-pin and 5-pin switches. Check the switch type your board takes before ordering, and match the feel you want: the YUNZII comes with linear Milk switches and the KiiBoom with linear Mochi switches, while the SOLAKAKA uses LEOBOG star vector switches.
Remove the keycap and the old switch
Unplug the keyboard first, then pull the keycap off with a keycap puller. The SOLAKAKA A99 Pro comes with a keycap puller in the box. Grip the switch from its top and bottom edges and pull it straight up out of the socket. Pull straight up so the pins come out cleanly, and set the old switch aside.
Press the new switch into place
Line up the pins on the new switch with the holes in the socket and press the switch straight down until it sits flat against the plate. Check that the switch is level and that it does not wobble when you press it. Then push the keycap back on and press the key a few times to check that it registers.
Check the keys after the swap
After you fit the new switches, plug the keyboard back in and press every key you changed to check that each one registers. If a key does not register, pull the switch out and check that its pins are straight and lined up with the socket. A switch that sits crooked or has a bent pin will not make contact, so reseat it before you keep typing.
What you need

AULA S99 Gaming Keyboard
A membrane keyboard with a 96% layout and RGB backlight that does not support hot-swapping, so it is not made for replacing switches.
View on Amazon
YUNZII B98 PRO 96% Wireless Mechanical Keyboard (Blue
A hot-swappable 96% mechanical keyboard with pre-lubed Milk linear switches that accepts both 3-pin and 5-pin switches.
View on Amazon
SOLAKAKA A99 Pro Mechanical Keyboard
A full hot-swappable 96% keyboard with LEOBOG star vector switches that supports 3-pin and 5-pin switches and comes with a keycap puller.
View on Amazon
KiiBoom Phantom98 Lite 96% Wireless Mechanical Gaming Keyboard
A hot-swappable 96% mechanical keyboard with pre-lubed Mochi linear switches that lets you change switches without soldering.
View on AmazonThese come from our ranked list Best 96 Keyboard, which compares them spec by spec.
FAQ
Do all keyboards let you replace switches?
No. Only hot-swappable mechanical keyboards let you pull switches out without soldering. The AULA S99 is a membrane keyboard and does not support hot-swapping, so its switches cannot be swapped the same way.
Do I need to solder new switches?
No, not on a hot-swappable keyboard. The YUNZII B98 PRO, SOLAKAKA A99 Pro and KiiBoom Phantom98 Lite all let you swap switches without soldering. On a soldered board you would need to desolder the old switch first, so check your board before you start.
What is the difference between 3-pin and 5-pin switches?
The number counts the pins on the bottom of the switch. A 5-pin switch has two extra plastic pins that hold it steady in the socket. Boards such as the YUNZII B98 PRO and SOLAKAKA A99 Pro accept both types, so either fits.
Can I mix different switches on one keyboard?
Yes. On a hot-swappable board you can fit a different switch under any key, so you can try a new feel on a few keys first. Make sure each switch matches the pin type your board takes before you press it in.




