How to Remove Keyboard Stabilizers
To remove keyboard stabilizers, unplug the keyboard, pull the keycaps off the long keys with a keycap puller, then unclip the stabilizer housings and wire from the plate. On a hot-swappable board you can pull the nearby switches for access, while a membrane board needs the maker's manual before you go further. Keep the parts together so each stabilizer goes back on the same key.
Unplug the keyboard and check the manual
Shut the keyboard down or switch it off, unplug the cable, and remove the wireless receiver if it uses one. Read the maker's manual for your model before you open anything, and contact the maker if the keyboard is still covered by its warranty. The YUNZII B98 PRO, SOLAKAKA A99 Pro, and KiiBoom Phantom98 Lite are hot-swappable, while the AULA S99 does not support hot-swapping, so the steps below fit the hot-swappable boards. Work on a clear desk with a tray for the keycaps and small parts.
Pull the keycaps off the long keys
Fit a keycap puller around a long keycap such as the spacebar and pull straight up until it comes free. Work through the other long keys the same way, pulling each cap straight up so the stems do not bend. The SOLAKAKA A99 Pro comes with a keycap puller. Set each keycap aside in the order it came off the board, so the same cap goes back on the same key.
Unclip the stabilizers from the plate
With the caps off, you can see the stabilizer housings and the wire under each long key. On a hot-swappable board, pull the switches beside a stabilizer if they get in the way of the housings, using a switch puller. Then lift each housing straight up out of the plate and lift the wire free, keeping the housings and wire of each stabilizer together. Do not force a housing that will not move; check the manual for how that model holds its stabilizers.
Clean the area and refit the parts
Wipe the plate around each stabilizer mount with a dry cloth and clear away any dust or debris. To refit a stabilizer, set the housings back into the plate and seat the wire in the housings, then press the keycap back on and check that the key moves down evenly. The YUNZII, SOLAKAKA, and KiiBoom boards ship with pre-lubricated stabilizers, so keep the lube on the wires when you refit them. If a stabilizer still rattles or sticks, take it out again and check that the wire sits fully in each housing.
What you need

AULA S99 Gaming Keyboard
A 96% membrane keyboard with 99 keys, RGB backlight, and a number pad that does not support hot-swapping.
View on Amazon
YUNZII B98 PRO 96% Wireless Mechanical Keyboard (Blue
A 96% hot-swappable mechanical keyboard with pre-lubed switches and tuned stabilizers, QMK/VIA support, and a gasket mount.
View on Amazon
SOLAKAKA A99 Pro Mechanical Keyboard
A 96% hot-swappable keyboard with pre-lubricated stabilizers, LEOBOG star vector switches, and a keycap puller.
View on Amazon
KiiBoom Phantom98 Lite 96% Wireless Mechanical Gaming Keyboard
A 96% hot-swappable keyboard with pre-lubricated stabilizers, a gasket mount, and VIA support for remapping keys.
View on AmazonThese come from our ranked list Best 96 Keyboard, which compares them spec by spec.
FAQ
Do I need to remove the switches to remove stabilizers?
On a hot-swappable board, pull the switches beside the stabilizer if they get in the way of the housings. The YUNZII B98 PRO, SOLAKAKA A99 Pro, and KiiBoom Phantom98 Lite are hot-swappable, so their switches lift out without soldering.
Can I remove stabilizers from a membrane keyboard?
The AULA S99 is a membrane keyboard and does not support hot-swapping, so do not force its switches or stabilizers out. Read its manual and contact the maker before you open it.
What tool do I need to pull the keycaps off?
A keycap puller fits around the cap and pulls it straight up off the stem. The SOLAKAKA A99 Pro comes with a keycap puller, and you can use any puller that fits the caps on your board.
Why does a key stick after I refit the stabilizer?
Check that the wire sits fully in each housing and that the keycap sits straight on the stems. If the key still sticks, take the stabilizer out again, check the housings and wire, and refit them.




