How to Install Keyboard Stabilizers
To install keyboard stabilizers, remove the keycaps and switches from the stabilized keys, take out the old stabilizers, lubricate the new ones, clip them into the plate or PCB, then refit the switches and keycaps and press each key to check for rattle. The job fits a hot-swappable keyboard; a soldered board needs the switches desoldered first. Work on a clear desk and keep the small parts together.
Check your keyboard supports the swap
Stabilizers sit under the long keys, such as the spacebar, Enter, Shift and Backspace, and they keep those keys level when you press them off-center. The swap is straightforward on a hot-swappable board, where the switches pull out without solder. On a soldered board the switches must come out with a soldering iron, which is a bigger job. A membrane keyboard has a different build, so the steps below are written for a mechanical board with removable switches. Check your keyboard manual for the stabilizer type and layout before you order parts.
Remove the keycaps and switches
Unplug the keyboard and place it on a clear surface. Pull the keycaps off the stabilized keys with a keycap puller, lifting straight up so the stems stay intact. Then pull each switch straight up with a switch puller until it comes free of the plate. Keep the keycaps and switches in order on the desk so each one goes back in the same spot. Do not force a switch that resists; check that the puller grips both sides before you pull again.
Take out the old stabilizers
With the switches out, you can see the stabilizer housings and the wire that joins them. Unhook the wire from the housings, then unclip each housing from the plate or lift it from the PCB. Note how the wire sits before you remove it, since the new wire goes back in the same way. Set the old parts aside.
Lubricate the new stabilizers
Put a thin coat of lubricant on the inside of each housing where the stem slides, on the stem itself, and on the ends of the wire where it meets the housings. A small brush gives an even coat and keeps lubricant off the plate. Wipe away any excess so it cannot drip onto the PCB. Lubricant cuts the rattle that makes stabilized keys sound loose, so cover each contact point and leave the wire bends clean.
Seat the stabilizers and check the keys
Clip each housing into the plate or PCB until it sits flat, then hook the wire into the housings the same way the old wire sat. Push the switches back into the plate until they click, then press the keycaps back onto the stems. Press each stabilized key at its center and at its edges and listen for rattle. If a key still rattles, lift the switch and reseat the wire before you put the keyboard back together.
What you need

AULA S99 Gaming Keyboard
A 96% membrane keyboard with 99 keys, RGB backlight and tri-mode connections, without hot-swapping support.
View on Amazon
YUNZII B98 PRO 96% Wireless Mechanical Keyboard (Blue
A hot-swappable 96% keyboard with pre-lubed switches and tuned stabilizers, a gasket mount and QMK/VIA support for remapping keys.
View on Amazon
SOLAKAKA A99 Pro Mechanical Keyboard
A hot-swappable 96% keyboard with pre-lubricated stabilizers, a gasket structure, an LCD screen and a metal knob.
View on Amazon
KiiBoom Phantom98 Lite 96% Wireless Mechanical Gaming Keyboard
A hot-swappable 96% keyboard with pre-lubricated stabilizers, a gasket mount and VIA support for custom key mapping.
View on AmazonThese come from our ranked list Best 96 Keyboard, which compares them spec by spec.
FAQ
Can I install stabilizers on a membrane keyboard?
The steps here are written for mechanical keyboards with removable switches. A membrane keyboard has a different construction, so check your keyboard's manual before taking it apart.
Do I need to lubricate new stabilizers?
Lubrication is optional. A thin coat on the housing sliders, the stem and the wire ends cuts rattle, so apply it before you clip the stabilizer in and wipe away any excess.
Why does a key still rattle after new stabilizers?
Check that the wire is seated fully in the housings and that the stabilizer is clipped tight to the plate or PCB. A wire that sits loose or a housing that is not level lets the key wobble, so reseat both and press the key again.




