Amazon Black Friday Week deals

Paid link

Keyboards & Mice · How-to guide

How to Clean Keyboard Stabilizers

We earn a commission when you buy through our links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Short answer

To clean keyboard stabilizers, unplug the keyboard, pull the large keycaps, take each stabilizer apart, wash the housings, stems and wire, let every part dry, then add a thin layer of lubricant and refit everything. Cleaning removes dust and old lubricant that make wide keys rattle, stick or feel scratchy.

  1. Unplug the keyboard and remove the keycaps

    Disconnect the keyboard from the computer or switch it off, so no key press registers while you work. Pull the wide keycaps that sit on stabilizers, such as the spacebar, Shift, Enter and Backspace, straight up with a keycap puller. Wide keys also hold small inserts on the stabilizer stems, so keep each keycap with its inserts and set them aside in order.

  2. Take the stabilizers apart

    Each stabilizer has two housings, two stems and a wire. Unclip the housings from the plate or unclip them from the board, then slide the wire out of the stems and keep one stabilizer's parts together. Check the maker's manual for your keyboard before opening the case, and do not open a keyboard that is still under warranty if the manual says to contact the maker instead.

  3. Wash and dry every part

    Wash the housings, stems and wire in warm water with a drop of mild soap, using a soft brush to reach the stem rails. Wipe old lubricant off the wire ends with a cloth lightly dampened with isopropyl alcohol. Rinse the soap off, shake off the water and let every part dry fully before you add lubricant, since trapped water thins the lubricant and leaves the key feeling rough.

  4. Re-lubricate and refit the parts

    Put a thin layer of keyboard lubricant on the ends of the wire where it meets the stems and a light coat on the stem rails. Too much lubricant makes a key feel slow, so wipe off any excess. Seat the wire back into the stems, clip the housings in place, then press each wide keycap down until it seats on the switch and both stabilizer stems. Press each key several times to check it travels evenly.

  5. If a stabilizer still rattles

    A rattle after cleaning points to a part that is not seated. Check that the wire sits in both stem clips, that each housing is clipped flat, and that the inserts in the keycap grip the stems. A key that sticks or returns slowly points to too much lubricant or a stem that is not fully dry, so take that one stabilizer apart again and wipe the excess off.

What you need

AULA S99 Gaming Keyboard

AULA S99 Gaming Keyboard

A membrane keyboard that does not support hot-swapping, so stabilizer cleaning stays at the keycap and surface level.

View on Amazon
YUNZII B98 PRO 96% Wireless Mechanical Keyboard (Blue

YUNZII B98 PRO 96% Wireless Mechanical Keyboard (Blue

A hot-swappable keyboard with pre-lubed switches and tuned stabilizers, so the stabilizers come out for cleaning and fresh lubricant.

View on Amazon
SOLAKAKA A99 Pro Mechanical Keyboard

SOLAKAKA A99 Pro Mechanical Keyboard

A hot-swappable keyboard with pre-lubricated stabilizers that comes with a keycap puller for removing the wide keys.

View on Amazon
KiiBoom Phantom98 Lite 96% Wireless Mechanical Gaming Keyboard

KiiBoom Phantom98 Lite 96% Wireless Mechanical Gaming Keyboard

A hot-swappable keyboard with pre-lubricated stabilizers and VIA support for remapping keys after the board goes back together.

View on Amazon

These come from our ranked list Best 96 Keyboard, which compares them spec by spec.

FAQ

How often should I clean keyboard stabilizers?

Clean them when a wide key rattles, sticks, returns slowly or feels scratchy, since those are signs of dust or worn lubricant. A key that still travels evenly and quietly does not need to come apart.

Can I clean stabilizers without removing them?

You can wipe around the stems and housings with a dry cloth or a cloth lightly dampened with isopropyl alcohol once the keycaps are off. A full clean of the wire and stem rails needs the stabilizer taken apart.

What if my keyboard does not support hot-swapping?

Keep the work at keycap level: pull the wide keycaps, wipe the exposed parts and refit the caps. Check the maker's manual before opening the case, and contact the maker about service while the keyboard is under warranty.

Ranked keyboards guides