How to Add Foam to a Keyboard
Adding foam to a keyboard means placing thin foam inside the case to change how the board sounds and feels when you type. The foam sits under the plate or at the bottom of the case, where it damps vibration and fills empty space. You open the keyboard, cut the foam to fit, lay it in place and reassemble the board, then type on it to hear the change.
Pick the foam and check the keyboard
Start with foam made for keyboards, such as case foam, plate foam or switch pads, and keep the sheets clean and flat until you use them. Switch the keyboard off and unplug it, or remove the batteries if it uses them, before you open anything. Check the warranty terms first, since opening the keyboard can change what the warranty covers. Look at how the case comes apart and whether the switches are hot-swappable or soldered, and follow the maker's manual for your keyboard.
Open the case and take out the plate
Remove the keycaps with a keycap puller and set them aside in order so they go back on the right keys. Unscrew the case screws and keep them in a small tray, then lift the top case away from the bottom. Lift the plate and circuit board out as one piece where the design allows it, and keep the cable between the board and the case connected if it does not come apart easily.
Cut the foam to fit the case
Lay the foam sheet on the bottom of the case and mark the outline with a pen, including the cutouts for the battery, the cable and the screw posts. Cut along the marks with clean scissors or a sharp blade on a flat surface, and hold the foam flat while you cut so it does not stretch. Check the fit by laying the foam in the case: it should sit flat without bunching at the edges or covering a screw post.
Lay the foam in and reassemble
Set the foam into the bottom of the case and press it flat so it touches the case all over. Place the plate and circuit board back on top of the foam, then refit the top case and fasten the screws a little at a time so the case closes evenly. Put the keycaps back on the right switches, plug the keyboard in or switch it on, and check that every key works.
Listen and adjust the foam
Type a few lines and listen for the change: the keys should sound softer and the case should ring less than before. If a key feels dull or does not press down fully, open the case again and check that no foam sits under a switch or over a screw post. Trim or remove foam a little at a time until the keys feel even across the board, and keep the spare foam for a later change.
What you need

AULA S99 Gaming Keyboard
A 96% membrane keyboard with 99 keys, a number pad, RGB backlight and tri-mode wireless, which does not support hot-swapping.
View on Amazon
YUNZII B98 PRO 96% Wireless Mechanical Keyboard (Blue
A 96% wireless mechanical keyboard with a gasket mount, five-layer filling structure, hot-swappable Milk switches and RGB backlight.
View on Amazon
SOLAKAKA A99 Pro Mechanical Keyboard
A 96% wireless mechanical keyboard with an LCD screen, a metal knob, a gasket structure and hot-swappable LEOBOG switches.
View on Amazon
KiiBoom Phantom98 Lite 96% Wireless Mechanical Gaming Keyboard
A 96% wireless mechanical keyboard with a gasket mount, hot-swappable Mochi switches, RGB backlight and an 8000mAh battery.
View on AmazonThese come from our ranked list Best 96 Keyboard, which compares them spec by spec.
FAQ
Does foam change how a keyboard sounds?
Foam damps vibration inside the case, so the keys sound softer and the hollow ring of the empty case fades. The change is in sound and feel only; the switches and keycaps stay the same, so the typing action does not change.
Can I add foam to any keyboard?
No. The case must open and leave room for foam under the plate or at the bottom. A membrane keyboard needs a different approach from a mechanical board, and a keyboard with soldered switches is harder to open than one with hot-swappable switches.
What foam goes inside a keyboard?
Case foam fills the bottom of the case, plate foam sits between the plate and the circuit board, and switch pads sit under the switches. Use foam made for keyboards and cut it to fit, since foam that is too thick can stop the case from closing.




